Lift Cylinder Mounts (Bulldozer) - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Description     | Qty     |
A     | 138-7574     | Link Bracket     | 2     |
B     | 1P-7407     | Eyebolt     | 1     |
Start By:
- Remove the bulldozer lift cylinder. Refer to Disassembly and Assembly, "Lift Cylinder (Bulldozer) - Remove".
- Install Tooling (A) and a suitable lifting device to yoke (1). The weight of yoke (1) is approximately 42 kg (93 lb).
Show/hide table
Illustration 1 | g01267042 |
- Remove bolts (2) and cover (3).
- Install Tooling (B) in pin (4). Remove pin (4) .
Show/hide table
Illustration 2 | g01267043 |
- Remove yoke (1) .
- Remove lip seal (5) .
Show/hide table
Illustration 3 | g01267049 |
- Remove sleeve bearings (6) .
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Description     | Qty     |
A     | 138-7574     | Link Bracket     | 2     |
C     | 5P-0960     | Grease Cartridge     | 1     |
- Lower the temperature of sleeve bearings (6). Install bearings (6) in the radiator guard with the grooves in bearings (6) within Angles (X). The sleeve bearings should have these dimensions after the installation:
- Angle (X) should be a maximum of 15 degrees.
- The inner bearing diameter should be 89.22 ± 0.05 mm (3.513 ± 0.006 inch).
- The outer bearing diameter should be 114.30 ± 0.065 mm (4.500 ± 0.006 inch).
Show/hide table
Illustration 4 | g01267049 |
Show/hide table
Illustration 5 | g00839813 |
- Install lip seal (5) into the radiator guard with the lip toward the outside.
- Fill the bore in the radiator guard with Tooling (C) .
- Attach Tooling (A) and a suitable lifting device to yoke (1). The weight of yoke (1) is approximately 42 kg (93 lb). Install yoke (1) .
Show/hide table
Illustration 6 | g01267051 |
- Install pin (4) .
- Install cover (3) and bolts (2). Remove Tooling (A) from yoke (1) .
Show/hide table
Illustration 7 | g01267042 |
End By: Install the bulldozer lift cylinder. Refer to Disassembly and Assembly, "Lift Cylinder (Bulldozer) - Install".
Caterpillar Information System:
AccuGrade® GPS (CD700) Plan View
854K Wheel Dozer Seat
Underground Articulated Trucks Truck Payload Measurement System Truck Payload Measurement System Troubleshooting
Underground Articulated Trucks Truck Payload Measurement System General Information
Underground Articulated Trucks Truck Payload Measurement System System Schematic
2006/05/01 The Joystick On Small Track-Type Tractors Has Been Replaced {4122, 5705}
AccuGrade® GPS (CD700) Display Navigation
AccuGrade® GPS (CD700) Startup
938H and IT38H Wheel Loader and Integrated Tool Carrier Power Train Temperature Sensor (Transmission Oil)
C9 On-highway Engine Cylinder Block Cover Group
938H and IT38H Wheel Loader and Integrated Tool Carrier Power Train Speed Sensor (Torque Converter Output) (Transmission Output)
D7R Series II Track-Type Tractor Machine Systems Piston Pump (Steering and Implement) - Install
The Front Housing on C9 Engines is Cracking{1151} The Front Housing on C9 Engines is Cracking{1151}
854K Wheel Dozer Battery Disconnect Switch
854K Wheel Dozer Backup Alarm
C4.4 Industrial Engine Power Sources
854K Wheel Dozer Parking Brake
938H and IT38H Wheel Loader and Integrated Tool Carrier Power Train Clutch (Forward High, Forward Low)
C4.4 Industrial Engine Glossary of Electronic Control Terms
AccuGrade® GPS (CD700) Cross Section View
AccuGrade® GPS (CD700) Profile View
AccuGrade® GPS (CD700) Text View
D6N Track-Type Tractor Hydraulic System Control Valve (Bulldozer Lift)
854K Wheel Dozer Engine Starting with Auxiliary Start Receptacle