MID 082 - CID 2114 - FMI 04
产生此代码的情况:
Show/hide table
图 1 | g01625217 |
"铲刀控制手柄示意图" |
"触发开关(推土铲控制手柄)"的两个输入状态都接地后会记录该诊断代码。
该诊断代码可能的原因如下:
- 短路至接地
- 开关有故障。
- ECM 存在故障。 但这种可能性很小。
系统响应:
机器响应如下:
- 将会出现一个 2 级警告。
- "自动铲刀辅助"功能和 "Accugrade" 功能将停用。
- "铲刀倾斜模式"不可用。
注: 确保该诊断代码为现行状态。 以下步骤可能会导致记录新的诊断代码。 可忽略生成的这些诊断代码。 完成测试步骤后,清除生成的诊断代码。
测试步骤 1. 检查是否对接地短路。
- 将钥匙起动开关转到 OFF(断开)位置。
- 从 ECM 上断开机器线束接头 J1 和 J2。
- 在机器线束接头 J1 上,测量触针 J1-33 和触针 J1-34 与所有可能的接地源之间的电阻。
预期结果:
每个电阻测量值都应大于 5000 欧姆。
结果:
- 正常 - 各电阻测量值都大于 5000 欧姆。 转至测试步骤 2。
- 异常 - 一个或多个电阻测量值小于 5000 欧姆。
修复: 电阻测量值偏低的电路短路。 修理或更换线束。 确认故障已排除。
停止
测试步骤 2. 检查开关的电阻。
- 钥匙起动开关和断路开关保持在 OFF(断开)位置。
- J1 和 J2 接头保持与 ECM 断开的状态。
- 从 "铲刀控制手柄"上断开机器线束。
- 将开关置于常开位置。 测量铲刀控制手柄接头的触针 10 与触针 5 之间的开关电阻。 已按下开关。
- 将开关置于常闭位置。 测量铲刀控制手柄接头的触针 11 与触针 5 之间的开关电阻。 没有按下开关。
预期结果:
每个电阻测量值都应小于 5 欧姆。
结果:
- 正常 - 各电阻测量值都小于 5 欧姆。 开关正常。
修复: ECM 出故障的可能性非常小。 退出并重新执行本测试步骤。 如果没有找到产生该诊断代码的原因,则应更换机具 ECM。 请参考故障诊断与排除, "电子控制模块 (ECM) - 更换"。
停止
- 异常 - 一个或两个电阻测量值不小于 5 欧姆。
修复: 开关有故障。 更换"铲刀控制手柄"。 执行铲刀控制手柄的标定步骤。 请参考您的机器的维修手册中的测试和调整, "标定"步骤。 确认使用新铲刀控制手柄后排除该故障。
停止
Caterpillar Information System:
3306C Engines for Caterpillar Built Machines Fuel Injection Nozzle - Test
D8T, D9T, D10T and D11T Track-Type Tractors MID 082 - CID 2114 - FMI 03
621G, 623G and 627G Wheel Tractor-Scrapers Wheel Tractor Power Train Bowl Conversion (Fuel Tank, Ladders, Steps)
D10T Track-Type Tractor Power Train Track Roller Frame - Install
930G Wheel Loader Steering System Piston Pump (Steering, Implement, Pilot)
924H, 924HZ, 928HZ and 930H Wheel Loaders Machine Systems Main Control Valve - Assemble
924H, 924HZ, 928HZ and 930H Wheel Loaders Machine Systems Main Control Valve - Disassemble
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Transmission Oil - Change
D9T Track-Type Tractor Engine Supplement Alternator - Remove and Install
D8T Track-Type Tractor Machine Systems Hydraulic Tank - Remove
621G, 623G and 627G Wheel Tractor-Scrapers Machine Systems Radiator Cap
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Test
D10T2 Track-Type Tractor Power Train Pivot Shaft - Remove and Install
980H Wheel Loader Engine Air Filter Secondary Element - Replace
D8T Track-Type Tractor Machine Systems Hydraulic Tank - Install
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System Tilt Cylinder (Tilt and Tip Function)
D8T, D9T, D10T and D11T Track-Type Tractors Power Train Oil - D8T and D9T
AD55 Underground Articulated Truck Power Train Axle Shaft - Remove
AD55 Underground Articulated Truck Power Train Axle Shaft - Install
AD30 Underground Articulated Truck C15 Engine Supplement Radiator - Install
AD30 Underground Articulated Truck Machine Systems Hoist Cylinder - Install
AD30 Underground Articulated Truck Machine Systems Hoist Cylinder - Remove
AD30 Underground Articulated Truck C15 Engine Supplement Engine and Torque Converter Updrive Gears - Remove
D9T Track-Type Tractor Engine Supplement Engine Oil Filter Base - Remove