MID 082 - CID 2114 - FMI 03
产生此代码的情况:
Show/hide table
图 1 | g01625217 |
"铲刀控制手柄示意图" |
以下步骤适用于触发开关"(铲刀控制手柄)"。 该开关与 ECM 之间有两个输入: "常开"(导线 J991-OR) 和 "常闭"(导线 J996-BR). 正常工作期间,一个开关输入开路,而另一个输入接地。 如果这两个输入的状态相同,ECM 将会检测到一个诊断代码。 这两个开关输入都开路或对蓄电池正极短路时能检测到该诊断代码。
该诊断代码可能的原因如下:
- 两个输入都开路。
- 短路至蓄电池
- 开关出故障
- ECM 可能存在故障。 但这种可能性很小。
系统响应:
机器响应如下:
- 将会出现一个 2 级警告。
- "自动铲刀辅助"功能和 "Accugrade" 功能将停用。
- "铲刀倾斜模式"不可用。
注: 确保诊断代码 CID 2114 FMI 03 处于现行状态。 以下步骤可能会生成 ECM 可以检测到的其他诊断代码。 请忽略所产生的诊断代码,在排除原有诊断代码后将其清除即可。
测试步骤 1. 检查是否开路。
- 将断路开关和钥匙起动开关转到 OFF(断开)位置。
- 从 ECM 上断开 J1 机器线束接头。
- 当开关处于常开位置时,在 J1 机器线束接头上测量触针 J1-34-(导线J991OR)与触针 J1-13-(导线210BK)之间的电阻。 已按下开关。
- 当开关处于常闭位置时,在 J1 机器线束接头上测量触针 J1-33-(导线J996BR)与触针 J1-13-(导线210BK)之间的电阻。 没有按下开关。
预期结果:
每个电阻测量值都应小于 5 欧姆。
结果:
- 是 - 每个电阻测量值都小于 5 欧姆。 转至测试步骤 3。
- 否 - 一个或两个电阻测量值不小于 5 欧姆。 线束或开关有故障。 转至测试步骤 2。
测试步骤 2. 检查开关的电阻。
- 从 "铲刀控制手柄"上断开机器线束。
- 将开关置于常开位置。 测量"铲刀控制手柄"接头的触针 10 与触针 5 之间的开关电阻。 已按下开关。
- 将开关置于常闭位置。 测量铲刀控制手柄接头的触针 11 与触针 5 之间的开关电阻。 没有按下开关。
预期结果:
每个电阻测量值都应小于 5 欧姆。
结果:
- 正常 - 电阻测量值小于 5 欧姆。 开关正常。
修复: 机器线束有故障。 修理或更换机器线束。
停止
- 异常 - 一个或两个电阻测量值不小于 5 欧姆。
修复: 开关有故障。 更换"铲刀控制手柄"。 执行"铲刀控制手柄"的标定步骤。 请参考您的机器的维修手册中的测试和调整, "标定"步骤。 确认使用新铲刀控制手柄后排除该故障。
停止
测试步骤 3. 检查有无短路。
- 在机器线束接头 J1 上,测量触针 J1-33 和触针 J1-34 与 J1 和 J2 接头上的所有其他触针之间的电阻。
预期结果:
每个电阻测量值都应大于 5000 欧姆。
结果:
- 正常 - 各电阻测量值都大于 5000 欧姆。
修复: ECM 出故障的可能性非常小。 退出并重新执行本测试步骤。 确认诊断代码依然处于现行状态。 如果没有找到产生该诊断代码的原因,则应更换机具 ECM。 请参考故障诊断与排除, "电子控制模块 (ECM) - 更换"。
停止
- 异常 - 一个或多个电阻测量值不大于 5000 欧姆。
修复: 电阻测量值偏低的电路短路。 修理或更换线束。 确认故障已排除。
停止
Caterpillar Information System:
621G, 623G and 627G Wheel Tractor-Scrapers Wheel Tractor Power Train Bowl Conversion (Fuel Tank, Ladders, Steps)
D10T Track-Type Tractor Power Train Track Roller Frame - Install
930G Wheel Loader Steering System Piston Pump (Steering, Implement, Pilot)
924H, 924HZ, 928HZ and 930H Wheel Loaders Machine Systems Main Control Valve - Assemble
924H, 924HZ, 928HZ and 930H Wheel Loaders Machine Systems Main Control Valve - Disassemble
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Transmission Oil - Change
D9T Track-Type Tractor Engine Supplement Alternator - Remove and Install
D8T Track-Type Tractor Machine Systems Hydraulic Tank - Remove
621G, 623G and 627G Wheel Tractor-Scrapers Machine Systems Radiator Cap
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Test
D10T Track-Type Tractor Power Train Track Roller Frame - Remove
D8T, D9T, D10T and D11T Track-Type Tractors MID 082 - CID 0875 - FMI 04
3306C Engines for Caterpillar Built Machines Fuel Injection Nozzle - Test
D8T, D9T, D10T and D11T Track-Type Tractors MID 082 - CID 2114 - FMI 04
D10T2 Track-Type Tractor Power Train Pivot Shaft - Remove and Install
980H Wheel Loader Engine Air Filter Secondary Element - Replace
D8T Track-Type Tractor Machine Systems Hydraulic Tank - Install
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System Tilt Cylinder (Tilt and Tip Function)
D8T, D9T, D10T and D11T Track-Type Tractors Power Train Oil - D8T and D9T
AD55 Underground Articulated Truck Power Train Axle Shaft - Remove
AD55 Underground Articulated Truck Power Train Axle Shaft - Install
AD30 Underground Articulated Truck C15 Engine Supplement Radiator - Install
AD30 Underground Articulated Truck Machine Systems Hoist Cylinder - Install
AD30 Underground Articulated Truck Machine Systems Hoist Cylinder - Remove