Transmission Oil - Change
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 让机器运转几分钟,使变速箱机油热起来。
- 把机器停放在平地上。 将选装部件降至地面,并施加轻微的下压力。 接合停放制动器,然后关闭发动机。
- 卸下变速箱油排放螺塞 (2) 。 让变速箱油排放到适当的容器中。 清洁并安装排放螺塞。
Show/hide table
图 1 | g00763411 |
注: 为了可以够到磁性滤网总成,取下机器底部的变速箱护板。
- 更换变速箱油滤清器。
参考关于正确的更换程序,请参阅 操作和保养手册, "变速箱油滤清器 - 更换"。
- 卸下变速箱箱左侧的螺栓和盖。
- 卸下壳体的磁性滤网管总成 (3) 和吸入滤网 (4) 。 从磁性滤网管总成上卸下三块磁铁。
- 用清洁的不易燃的溶剂清洗磁性滤网管总成。
- 用布、硬毛刷或压缩空气来清洁磁铁。
Show/hide table
注意 |
---|
不可将磁铁掉落在硬物上或敲击硬物。 更换所有损坏的磁铁。 |
- 清洁盖并检查盖的密封。 如果密封损坏,则更换密封。
- 将三块磁铁装到磁性滤网管总成 (3) 上。 将吸入滤网 (4) 和磁性滤网管总成 (3) 装到壳体内。
- 安装盖和4个螺栓。
- 卸下机器左侧的变速箱加注口盖 (1) 。 通过变速箱加油管向变速箱加注油。
注: 垃圾填埋压实机配备保护加油管和目测表和护罩。 通过盖 (5) 接近加油管。 目测表可通过提升小检视门 (6) 来查看。
参考参阅操作和保养手册, "加注容量"。
Show/hide table
图 2 | g00776092 |
- 清洗并安装加注口盖。
- 卸下变速箱顶部的变速箱呼吸器 (8) 。 使用清洁、不易燃的溶剂来清洗变速箱呼吸器。 使变速箱呼吸器晾干。 然后安装变速箱呼吸器。
Show/hide table
图 3 | g01109361 |
- 起动发动机并在低怠速下运转。 接合行车制动器。 缓慢操作变速箱操纵杆,以使油得以循环。
- 将变速箱操纵杆移入空档(NEUTRAL)位置。 接合停放制动器,然后关闭发动机。 检查变速箱是否漏损。
- 检查变速箱油位。
参考请参考操作和保养手册, "变速箱油位 - 检查"。
Caterpillar Information System:
D9T Track-Type Tractor Engine Supplement Alternator - Remove and Install
D8T Track-Type Tractor Machine Systems Hydraulic Tank - Remove
621G, 623G and 627G Wheel Tractor-Scrapers Machine Systems Radiator Cap
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Test
D10T Track-Type Tractor Power Train Track Roller Frame - Remove
D8T, D9T, D10T and D11T Track-Type Tractors MID 082 - CID 0875 - FMI 04
D8T, D9T, D10T and D11T Track-Type Tractors MID 082 - CID 0875 - FMI 03
D8T, D9T, D10T and D11T Track-Type Tractors MID 082 - CID 0874 - FMI 04
D8T, D9T, D10T and D11T Track-Type Tractors MID 082 - CID 0874 - FMI 03
Supplemental Parts Information for the USN Seabee 924G Wheel Loader{0374, 7000} Supplemental Parts Information for the USN Seabee 924G Wheel Loader{0374, 7000}
SystemOne Track Guiding Arrangements {4170, 4177} SystemOne Track Guiding Arrangements {4170, 4177}
D8T Track-Type Tractor Machine Systems Hydraulic Tank - Assemble
924H, 924HZ, 928HZ and 930H Wheel Loaders Machine Systems Main Control Valve - Disassemble
924H, 924HZ, 928HZ and 930H Wheel Loaders Machine Systems Main Control Valve - Assemble
930G Wheel Loader Steering System Piston Pump (Steering, Implement, Pilot)
D10T Track-Type Tractor Power Train Track Roller Frame - Install
621G, 623G and 627G Wheel Tractor-Scrapers Wheel Tractor Power Train Bowl Conversion (Fuel Tank, Ladders, Steps)
D8T, D9T, D10T and D11T Track-Type Tractors MID 082 - CID 2114 - FMI 03
3306C Engines for Caterpillar Built Machines Fuel Injection Nozzle - Test
D8T, D9T, D10T and D11T Track-Type Tractors MID 082 - CID 2114 - FMI 04
D10T2 Track-Type Tractor Power Train Pivot Shaft - Remove and Install
980H Wheel Loader Engine Air Filter Secondary Element - Replace
D8T Track-Type Tractor Machine Systems Hydraulic Tank - Install
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Electrohydraulic System Tilt Cylinder (Tilt and Tip Function)