Piston Pump (Hydraulic Fan) - Assemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1P-0510 | Driver Group | 1 |
B | 1P-1858 | Pliers | 1 |
C | 8H-8581 | Feeler Gauge | 1 |
D | 8T-5096 | Indicator | 1 |
E | 1S-0256 | Pliers | 1 |
F | 1U-7978 | Screwdriver | 1 |
- Use the proper equipment to handle bearing (54). Heat bearing (54) to a maximum temperature of
121 °C (250 °F) . Install bearing (54) onto the shaft (49).Show/hide tableIllustration 2 g00670361 - Use the proper equipment to handle the bearing cup. Lower the temperature of bearing cup (53) and install the bearing cup in pump body (27).
Show/hide table
Illustration 3 g00670360 - Inspect the O-ring seals on plugs (52). Replace the O-ring seals, if necessary. Install two plugs (52) in pump body (27).
Show/hide table
Illustration 4 g00670531 Show/hide tableIllustration 5 g00670532 - Install snap ring (50). Use Tooling (A) to install seal (51) (not shown).
Show/hide table
Illustration 6 g00670298 - Install shaft assembly (49).
- Use the following steps to determine the proper preload on the bearings of the pump assembly.
- Use the proper equipment to handle the bearing cup. Lower the temperature of bearing cup (30) and install the bearing cup in head assembly (26).
Show/hide table
Illustration 8 g00670604 Typical Example - Install adjustment shim (33) and bearing (32) onto shaft (49).
Show/hide table
Illustration 9 g00670605 - Position head assembly (26) onto pump body (27).
Show/hide table
Illustration 10 g01088808 - Use Tooling (C) to measure the distance between the head and the pump housing.
- Take measurements at three equal intervals on the surface between the head and the pump housing.
- The average of the three dimensions should be between zero and
0.05 mm (.002 inch) . - If necessary, grind adjustment shim (33) in order to obtain the correct dimension between the head and the pump housing. It may be necessary to replace the shim with a new part.
Show/hide table
Illustration 11 g00670625 - Install four bolts (25) in the head and pump housing (27). Tighten bolts (25) to a torque of
100 ± 20 N·m (75 ± 15 lb ft) .Show/hide tableIllustration 12 g00670626 - Use Tooling (D), (E), and (F) to check end play in shaft (49). If end play exists in the shaft assembly, repeat Step 6 until the correct dimension between the head and the pump housing is reached.
- Remove bolts (25) and head assembly (26) from pump body (27). Remove bearing (32) and adjustment shim (33) from shaft (49).
- Proceed with the assembly of the fan drive pump.
Show/hide tableIllustration 7 g00669728 Show/hide tableIllustration 13 g00670223 - Use the proper equipment to handle the bearing cup. Lower the temperature of bearing cup (30) and install the bearing cup in head assembly (26).
- Install two swashplate bearings (48).
Show/hide table
Illustration 14 g00670207 - Install spring (47).
Show/hide table
Illustration 15 g00670206 - Install swashplate (46).
Show/hide table
Illustration 16 g00670205 Note: Note that there is a correct connection of the piston rod and the swashplate.
- Install piston rod (45).
Show/hide table
Illustration 17 g00670204 - Install the control piston (44).
Show/hide table
Illustration 18 g00669745 Show/hide tableIllustration 19 g00669744 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Note: There is spring force against lock ring (43). When lock ring (43) is not seated properly, the spring force will be released. Installation of the internal components in barrel (38) should be performed in a press. This is done in order to retain spring (42) and lock ring (43).
- Install pins (40), guide (41) and spring (42) in barrel (38).
- Use a press and Tooling (A) to compress the spring (42) in barrel assembly (38).
- Use Tooling (B) to install retaining ring (43).
- Slowly release compression on spring (42). Make sure that the retaining ring (43) is seated properly.
Show/hide table
Illustration 20 g00669743 - Install retaining ball (39) on barrel assembly (38).
Show/hide table
Illustration 21 g00669741 - Install piston assembly (37) in barrel assembly (38).
Show/hide table
Illustration 22 g00669742 - Install rotary group (36) onto the shaft. Make sure that the splines are aligned properly.
Show/hide table
Illustration 23 g00669732 - Inspect the O-ring seal on plug (34). Replace the O-ring seal, if necessary. Install plug (34).
Show/hide table
Illustration 24 g00669731 - Install the adjustment shim (33).
Show/hide table
Illustration 25 g00669730 - Install bearing (32) on the shaft.
Show/hide table
Illustration 26 g00669729 - Install O-ring (31).
Show/hide table
Illustration 27 g00669727 - Install O-ring seal (28) and port plate (29) on head assembly (26).
Show/hide table
Illustration 28 g00669722 - Install head assembly (26) and four bolts (25). The torque for the bolts (25) is
100 ± 20 N·m (75 ± 15 lb ft) .Show/hide tableIllustration 29 g00670203 - Install spool (23) in compensator valve (1). Install spacer (24) onto plug (22).
- Install plug (22) in compensator valve (1). The torque for the plug (22) is
30.5 ± 1.5 N·m (23 ± 1 lb ft) .Show/hide tableIllustration 30 g00670201 - Install O-ring seal (17) to plug (16). Install plate (18), spring (19), spring (20), and guide (21) in compensator valve (1).
- Install plug (16) in compensator valve (1). The torque for the plug (16) is
100 ± 5 N·m (75 ± 3 lb ft) .Show/hide tableIllustration 31 g00670198 - Install spool (14) in compensator valve (1). Install spacer (15) on plug (13).
- Install plug (13) in compensator valve (1). The torque for the plug (13) is
30.5 ± 1.5 N·m (23 ± 1 lb ft) .Show/hide tableIllustration 32 g00670195 - Install O-ring seal (8) to plug (7). Install plate (9), spring (10), spring (11), and guide (12) in compensator valve (1).
- Install plug (7) in compensator valve (1). The torque for the plug (7) is
80 ± 5 N·m (58 ± 3 lb ft) .Show/hide tableIllustration 33 g00670190 - Inspect the O-ring seals on plugs (5). Replace the O-ring seals, if necessary. Install two plugs (5) in compensator valve (1).
Show/hide table
Illustration 34 g00670188 - Inspect the O-ring seals (4) and replace the O-ring seals, if necessary. Install three O-ring seals (4) on compensator valve (1).
Show/hide table
Illustration 35 g00669721 - Install four bolts (2) and pressure and flow compensator valve (1) to fan drive pump (3). The torque for bolts (2) is
34 ± 3 N·m (25 ± 2 lb ft) .
Show/hide table
Illustration 1 | g00670525 |
End By:
- Install the fan drive pump. Refer to Disassembly and Assembly, "Piston Pump (Hydraulic Fan) - Install".
Caterpillar Information System:
824H Wheel Dozer, 825H Soil Compactor and 826H Landfill Compactor Machine Systems Piston Pump (Hydraulic Fan) - Disassemble
3054 Engine Finding Top Center Position for No. 1 Piston
980G Series II Wheel Loader Machine Systems Piston Pump (Hydraulic Fan) - Install
3054 Engine Fuel System Pressure - Test
3054 Engine Air Inlet Heater - Test
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Drive Shaft Support Bearing - Lubricate
2003/11/17 A New Angling Cylinder Is Now Used {5101}
2001/04/23 The Special Instruction, REHS0597, "Recommendation for Welding 2-Strap Bucket Adapters to Base Edges" is Available {6800, 6801, 6803}
980G Series II Wheel Loader Machine Systems Piston Pump (Hydraulic Fan) - Remove
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Drive Shaft Spline (Center) - Lubricate
2001/05/28 A New Arc Suppressor Eliminates Power to the Engine Shutoff Solenoid {1634}
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Cooling System Coolant (ELC) - Change
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Engine Air Precleaner - Clean
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Engine Crankcase Breather - Clean
3054 Engine Fuel System - Prime
Product Identification Numbers (PIN) Location Guide Stump Grinder
Product Identification Numbers (PIN) Location Guide Power Module
Product Identification Numbers (PIN) Location Guide Vibratory Compactor (Work Tool)
3054 Engine Fuel Injection Nozzle - Test
Product Identification Numbers (PIN) Location Guide Trencher
3054 Engine Automatic Timing Advance Unit - Test
621G and 627G Wheel Tractor-Scrapers Machine Systems Hydraulic Tank - Remove
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Power Train Systems MID 079 - CID 1705 - FMI 03
816F Landfill Compactor, 815F Soil Compactor and 814F Wheel Dozer Engine Oil (High Speed) and Oil Filter - Change - If Equipped