Camshaft - Install
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Make sure that the camshaft is clean. Lubricate the camshaft with clean engine oil.
Show/hide table
Illustration 1 g01129587 Typical example - Carefully install camshaft assembly (10) into the engine cylinder block (11). Be careful not to damage the lobes of the camshaft or the camshaft bearings.
Show/hide table
Illustration 2 g00828468 Typical example - Install camshaft retainer (9).
Note: The two cylinder and the three cylinder engines have a different camshaft retainer (9) and different fasteners (6) and (7), to the four cylinder engines. The removal procedure is similar for all models.
- Align the holes in camshaft retainer (9) with the holes in cylinder block (10).
For C0.5, C0.7, C1.1/3011C, C1.5/3013C and C1.6 engines, install the outer setscrew (6) and install the allen head screw (7).
For C2.2/3024C and C2.2/3024CT engines, install the setscrews (6) and (7).
Torque both fasteners to
11 N·m (8 lb ft) .Show/hide tableIllustration 3 g00828467 Typical example - When you install the idler gear, make sure that timing marks (2) are aligned on the following components:
- Crankshaft gear (3)
- Camshaft gear (4)
- Idler gear (5)
- Install idler gear (5). Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
- Install slider (1) to camshaft (4).
Note: Make sure that the notch on the base of slider (1) is engaged on the pin of camshaft gear (4).
End By:
- Install the engine front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
- Install the fuel priming pump. Refer to Disassembly and Assembly, "Fuel Priming Pump - Install".
- Install the lifters. Refer to Disassembly and Assembly, "Lifter Group- Remove and Install".
Caterpillar Information System:
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Filter Base - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Camshaft - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Fuel Transfer Pump - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Rocker Shaft - Assemble
390F MHPU Mobile Hydraulic Power Unit Engine Crankcase Breather - Clean
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Housing (Front) - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Housing (Front) - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Fuel Injection Nozzles - Install
C27 Engines for Track-Type Tractors CID 0007 FMI 05 Cylinder #7 Injector open circuit
C27 Engines for Track-Type Tractors CID 0007 FMI 06 Cylinder #7 Injector short
C27 Engines for Track-Type Tractors CID 0008 FMI 05 Cylinder #8 Injector open circuit
C27 Engines for Track-Type Tractors CID 0008 FMI 06 Cylinder #8 Injector short
C27 Engines for Track-Type Tractors CID 0009 FMI 05 Cylinder #9 Injector open circuit