C32 Marine Engines Caterpillar


Sensors and Electrical Connectors

Usage:

C32 RNC

Table 1
Connector     Function    
J1/P1     Electronic Control Module (ECM) Connector (70−Pin)    
J2/P2     ECM Connector (120−Pin)    
J60     Engine Service Tool Connector    
J61     Customer Connector (70-Pin)    
J67     J1939 Termination Resistor    
J69/P69     Marine Engine Control Panel    
J100/P100     Engine Coolant Temperature Sensor    
J103/P103     Intake Manifold Air Temperature Sensor    
J105/P105     Fuel Temperature Sensor    
J137/P137     Marine Transmission Oil Temperature Sensor    
J200/P200     Boost Pressure Sensor    
J201/P201     Engine Oil Pressure Sensor    
J209/P209     Fuel Pressure Sensor    
J212/P212     Marine Transmission Oil Pressure Sensor    
J300A/P300A     Injector Solenoid Harness (Left Bank)    
J300B/P300B     Injector Solenoid Harness (Right Bank)    
P400     Engine Timing Calibration    
J401/P401     Primary Engine Speed/Timing Sensor    
J402/P402     Secondary Engine Speed/Timing Sensor    
J800/P800     Engine Coolant Level Sensor    
J803/P803     Fuel Level Sensor    



Illustration 1g01130292

Components for the engine's control system

Component Location




Illustration 2g01130332

Component locations

The location of the fuel sensors depends on the engine's configuration.

(1) Connector for the injector solenoid harness (left bank)

(2) ECM

(3) Connector for engine timing calibration

(4) Engine coolant level sensor

(5) Secondary engine speed/timing sensor

(6) Engine oil pressure sensor

(7) Termination resistor

(8) Service tool connector

(9) Engine coolant temperature sensor

(10) Customer connector

(11) Boost pressure sensor

(12) Connector for the marine transmission oil temperature sensor

(13) Intake manifold air temperature sensor

(14) Connector for the marine transmission oil pressure sensor

(15) Connector for the fuel level sensor

(16) Fuel pressure sensor

(17) Primary engine speed/timing sensor

(18) Connector for the marine engine control panel (typical location)

(19) Connector for the injector solenoid harness (right bank)

(20) Fuel temperature sensor

Marine Engine Control Panel




Illustration 3g01125688

Marine engine control panel

(1) 15 amp circuit breaker for the control panel

(2) Maintenance clear switch

(3) Maintenance overdue lamp

(4) Engine shutdown switch

(5) Diagnostic lamp

(6) Hour meter

(7) Warning lamp

(8) Keyswitch

Caterpillar Information System:

3508C, 3512C and 3516C Marine Engines Crankshaft Main Bearings - Remove
3508C, 3512C and 3516C Marine Engines Crankshaft Main Bearings - Install
854G Wheel Dozer High Intensity Discharge Lamp (HID) - Replace - If Equipped
3500 Engines Connecting Rod Bearings - Remove and Install
345C, 365C and 385C Excavators Air Conditioning and Heating Air Conditioner Lines
3508C, 3512C and 3516C Marine Engines Pistons and Connecting Rods - Install
3508C, 3512C and 3516C Marine Engines Pistons and Connecting Rods - Remove
C7 On-Highway Engine Water Pump - Install
C7 Engines for Caterpillar Built Machines Water Pump - Assemble
C7 Engines for Caterpillar Built Machines Water Pump - Disassemble
C7 On-Highway Engine Water Pump - Remove
3500B and 3500 Marine Propulsion Engines with EUI Option Belts - Inspect/Adjust/Replace
345 MHPUC Mobile Hydraulic Power Unit Machine System Specifications Relief Valve (Main) - Heavy Lift
2004/12/01 A Different Starting Motor is Used {1451}
345C Excavator Machine System Specifications Relief Valve (Main)
C11 and C13 Engines Fan Drive
2004/12/01 A New Aftercooler Cover is Now Used {1063, 1063}
2004/12/01 An Improved Engine Mount is Now Used {1152}
345C Excavator Machine System Specifications Hydraulic Tank and Filter
3500B Marine Propulsion Engines Refill Capacities and Recommendations
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Remove
3508C, 3512C and 3516C Marine Engines Accessory Drive (Front) - Install
2006/02/01 Magnetic Cover for the Turbocharger Oil Supply Line {1052, 1307}
2006/02/20 Magnetic Cover for the Turbocharger Oil Supply Line {1052, 1307}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.