Compression Brake - Disassemble
解体步骤
开始:
- 拆卸压缩制动器。 请参考解体与组装, "压缩制动器 - 拆卸"。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下机油管子 (1) 和 (2) 。 拆下 O 形密封圈。
注: 如果 O 型密封圈磨损或损坏，则应使用新零件更换。
Show/hide table
 | |
| 图 1 | g00471083 |
- 拆下卡环 (7) 、杯 (6) 、隔套 (5) 、弹簧 (4) 和 (3) 以及活塞 (8) 。
Show/hide table
 | |
| 图 2 | g00471084 |
- 拆下三个挡圈 (13) 。 从压缩制动器的三个位置拆下卡子 (12) 、弹簧 (11) 和 (10) 以及活塞 (9) 。
Show/hide table
 | |
| 图 3 | g00471085 |
- 拆下三根螺栓 (15) 、垫圈 (16) 、卡子 (17) 和活塞 (14) 。
Show/hide table
 | |
| 图 4 | g00471086 |
Caterpillar Information System:
D9R Track-Type Tractor Fuel Tank and Fuel System Water Separator - Drain
D8R Track-Type Tractor Ether Starting Aid Cylinder - Replace
963C Track-Type Loader Machine Systems Tilt Cylinder - Disassemble
615C Series II Wheel Tractor-Scraper Wheel Tractor Power Train Selector Valve (Torque Converter Lockup Clutch) - Assemble
902 and 906 Compact Wheel Loaders Steering System Visual Inspection
3304B and 3306B Engines for Caterpillar Built Machines Compression Brake - Install
D8R Track-Type Tractor Engine Air Precleaner - Clean
631E Series II Wheel Tractor-Scrapers Differential and Final Drive Oil Sample - Obtain
G3B, K3A and L3A Denso Alternators Component Description
953C Track-Type Loader Machine Systems Refrigerant Evaporator Coil - Install
3304B and 3306B Engines for Caterpillar Built Machines Compression Brake - Remove
3406E and 3456 Engines for Caterpillar Built Machines General Information
980G Wheel Loader Hydraulic System Pilot Valve (Oil Manifold)
963C Track-Type Loader Machine Systems Tilt Cylinder - Assemble
3406E and 3456 Engines for Caterpillar Built Machines Air Inlet and Exhaust System
3304B and 3306B Engines for Caterpillar Built Machines Compression Brake - Assemble
615C Series II Wheel Tractor-Scraper Wheel Tractor Power Train Selector Valve (Torque Converter Lockup Clutch) - Install
980G Wheel Loader Hydraulic System Pressure Reducing Valve
G3B, K3A and L3A Denso Alternators Normal Operation
615C Series II Wheel Tractor-Scraper Wheel Tractor Power Train Slip Joint - Remove and Install
902 and 906 Wheel Loaders Power Train Piston Pump (Hydrostatic) - Remove
980G Wheel Loader Hydraulic System Solenoid Valve (Pilot Proportioning)
980G Wheel Loader Hydraulic System Implement Electronic Control Pinout Specifications
3406E and 3456 Engines for Caterpillar Built Machines Electrical System