Fuel Injection Lines
Show/hide table
Illustration 1 | g01362841 |
Top view of the engine |
(1) Fuel lines
-
Tighten the fuel line nuts.
- Torque ... 40 ± 7 N·m (30 ± 5 lb ft)
(2) Lubricate the O-ring seal with diesel fuel.
Show/hide table
Illustration 2 | g01362847 |
View A-A |
(3) Tighten the retainers to the following torque. ... 48 ± 7 N·m (35 ± 5 lb ft)
(4) Tighten the nut to the following torque. ... 30 ± 7 N·m (22 ± 5 lb ft)
(5) Lubricate the bore lightly with clean diesel fuel.
Show/hide table
Illustration 3 | g01362839 |
The clamps for the fuel line are installed at the values that follow.
- Position (A) ... 564 ± 3 mm (22 ± 0.12 inch)
- Position (B) ... 495 ± 3 mm (19.5 ± 0.12 inch)
- Position (C) ... 429 ± 3 mm (17 ± 0.12 inch)
- Position (D) ... 345 ± 3 mm (14 ± 0.12 inch)
- Position (E) ... 275 ± 3 mm (11 ± 0.12 inch)
- Position (F) ... 220 ± 3 mm (8.7 ± 0.12 inch)
- Position (G) ... 215.2 mm (8.5 inch)
- Position (H) ... 170 ± 3 mm (7 ± 0.12 inch)
- Position (I) ... 155 ± 3 mm (6 ± 0.1 inch)
- Position (J) ... 167 ± 3 mm (6.6 ± 0.121 inch)
- Position (K) ... 53 ± 3 mm (2 ± 0.12 inch)
- Position (L) ... 587 ± 3 mm (23 ± 0.12 inch)
- Position (M) ... 486 ± 3 mm (19 ± 0.12 inch)
- Position (N) ... 440 ± 3 mm (17 ± 0.12 inch)
- Position (O) ... 425 ± 3 mm (17 ± 0.12 inch)
- Position (P) ... 225 ± 3 mm (9 ± 0.12 inch)
- Position (Q) ... 215.2 mm (8.5 inch)
- Position (R) ... 205 ± 3 mm (8 ± 0.12 inch)
- Position (S) ... 170 ± 3 mm (7 ± 0.12 inch)
- Position (T) ... 85 ± 3 mm (3 ± 0.12 inch)
- Position (B) ... 495 ± 3 mm (19.5 ± 0.12 inch)
Show/hide table
Failure to properly replace or install a fuel injection line clamp may lead to fuel line failure. Fuel line failure may result in a fire hazard, which may cause personal injury or death. The fuel injection line clamps must be installed per these specifications. |
Caterpillar Information System:
G3406 Engines Temperature Switch
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Model View Illustrations
2003/08/25 Repair Guidelines for Air Compressors {1803}
2003/09/01 Repair Guidelines for Air Compressors {1803}
2003/10/01 Repair Guidelines for Air Compressors {1803}
C4.4 Industrial Engine Engine Oil Pressure
C4.4 (Mech) Industrial Engine Electrical System
2003/12/01 New Parts Are Available for the Throttle {1266, 1269}
G3406 Engines Engine Oil Pressure Sensor
3412 Generator Set Engines Engine Oil Pressure Sensor
G3406 Engines Engine Oil Pressure Switch
G3406 Engines Coolant Temperature Contactor
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Symbols
G3406 Engines Circuit Breakers
3500B Series II Marine Engines Starting Motor System
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Modes Of Operation
G3406 Engines Governor Linkage - Woodward governor 1724
G3406 Engines Governor Linkage - PSG Governor
G3406 Engines Governor Linkage - Woodward Hydra-mechanical Governor
C13 Engine Fan Drive Mounting Group - Remove and Install
C18 Marine Generator Set Engines CID 0041 FMI 03 8 Volt DC Supply short to +batt
C18 Marine Generator Set Engines CID 0041 FMI 04 8 Volt DC Supply short to ground
3126B Industrial Engines CID 0100 FMI 04 Engine Oil Pressure short to ground
2003/09/01 A New Solenoid Provides Better Starting Conditions {1259}