Actuator Bypass Valve (Variable) - Install
安装步骤
- 将轮齿 (9) 和弹簧销 (8) 安装到阀组件 (5) 的轴上。
Show/hide table
图 1 | g02161253 |
- 插入弹簧销,直到弹簧销与轮齿外径平齐。
注: 外径为 4.7 mm (0.185 in) 的钻头可用于对齐轮齿的孔与轴孔。
Show/hide table
图 2 | g02112537 |
安装在轮齿和轴内的弹簧销的视图。 |
- 将弹簧 (10) 的一端装入弹簧销。
Show/hide table
图 3 | g02161293 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将轭 (11) 安装到弹簧 (10) 的另一端。 以顺时针方向转动轭 (11) ,这样便可以将轭 11 安装到轮齿 (9) 上。 旋转靠近弹簧。
Show/hide table
图 4 | g02161300 |
- 将第二个弹簧 (10) 安装到轭 (11) 的另一端。
Show/hide table
图 5 | g02124415 |
- 将适配器 (12) 安装到弹簧 (10) 的另一端。 以顺时针方向旋转适配器,这样便可以将适配器 (12) 安装在轭 (11) 上。 旋转靠近弹簧。
- 将新组装的阀组件 (5) 安装到支架 (7) 上。 将螺栓上紧到 41 N·m (30 lb ft) 的扭矩。
Show/hide table
图 6 | g02161586 |
- 以顺时针方向旋转执行器的轴,直到停止为止。
- 通过将适配器安装在接头 (4) 内,将新组装的阀组件 (5) 和支架 (7) 安装在执行器组件 (2) 上。
注: 确保阀组件的箭头指向气流方向。
Show/hide table
图 7 | g02161587 |
- 重新安装现有的安装坚固件,穿过执行器组件和支架。 拧紧固定螺母的螺栓 (6) 至扭矩为 45 N·m (33 lb ft)。
Show/hide table
图 8 | g02161591 |
- 确保执行器抵着闭合止动块。 以顺时针方向旋转执行器的轴。
- 确保螺栓 (13) 朝向进气端,阀组件上的箭头与气流方向一致。
Show/hide table
图 9 | g02161623 |
- 确保阀组件 (5) 中的板与气流方向垂直。
Show/hide table
图 10 | g02161624 |
- 拧紧螺钉 (3) 至扭矩为 15 N·m (11 lb ft),同时固定阀组件中的板,使其与气流方向垂直。
Show/hide table
图 11 | g02161625 |
- 安装卡箍组件 (1) 。
注: 安装前,请确认执行器旁通阀在正确方向上。
Show/hide table
图 12 | g02162953 |
- 接通气体供给。
Caterpillar Information System:
3500B Series II Marine Engines Digital Sensor Supply
345B Excavator Swing Drive Oil Sample - Obtain
C11 and C13 Engines for Caterpillar Built Machines Camshaft Bearings - Install
3408C, 3412C and 3412D High Performance Marine Engines Cylinder Liner
2003/08/01 Use the Correct Front Housing Bolts {1151}
Cat® Digital Voltage Regulator Poor Voltage Regulation - Troubleshoot
Cat® Digital Voltage Regulator No Line Loss Compensation - Troubleshoot
C15 On-Highway Engine Flywheel Housing
Cat® Digital Voltage Regulator No Voltage Droop - Troubleshoot
Cat® Digital Voltage Regulator Unstable Voltage - Troubleshoot
C15 Petroleum Generator Set Engines Housing (Front)
C11 and C13 Engines for Caterpillar Built Machines Camshaft Bearings - Remove
2003/08/01 New Oil Pump with a Longer Service Life {1304}
G3406 Engines Gas Solenoid Valve
C13 Engine Connecting Rod Bearings - Remove
C13 Engine Connecting Rod Bearings - Install
G3406 Engines Coolant Temperature Contactor
G3406 Engines Engine Oil Pressure Switch
3412 Generator Set Engines Engine Oil Pressure Sensor
G3406 Engines Engine Oil Pressure Sensor
2003/12/01 New Parts Are Available for the Throttle {1266, 1269}
C4.4 (Mech) Industrial Engine Electrical System
C4.4 Industrial Engine Engine Oil Pressure
2003/10/01 Repair Guidelines for Air Compressors {1803}