Cylinder Drift - Check - Loaded Bucket
Show/hide table
"Cylinder Drift - Check (Loaded Bucket)" | |||
---|---|---|---|
Item | New | Service Limit | Actual |
Boom Cylinder | |
|
|
Stick Cylinder | |
|
|
Bucket Cylinder | |
|
Show/hide table
Bucket Configuration Reference | |||
Model | Capacity | Weight | Load |
B1225HD | |
|
|
B1300GD | |
|
|
The performance level of the cylinder, the cylinder seals, and the overload relief valves for the implements can be determined with the following procedure.
Note: The machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.
Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".
Show/hide table
Required Tools | |
---|---|
Description | Qty |
Measuring Tape | 1 |
Stopwatch | 1 |
Show/hide table
Illustration 1 | g00298378 |
- Position the machine on level ground. Refer to Illustration 1.
- Load the bucket. Refer to Table 2 for the correct load weight of the bucket.
- Raise the boom until the top stick pin is the same height as the boom foot pin.
- Fully extend the bucket cylinder.
- Fully retract the stick cylinder.
- Extend the stick cylinder rod
70 mm (2.8 inch) from the fully retracted position. - Measure each cylinder length from cylinder pin to cylinder pin.
- Stop the engine.
- Leave the machine in this position for 3 minutes. Measure each cylinder length from cylinder pin to cylinder pin for drift.
Caterpillar Information System:
Installation of the 467-4861 Front Lines Gp on Certain Hydraulic Excavators {5057} Installation of the 467-4861 Front Lines Gp on Certain Hydraulic Excavators {5057}
M314F, M316F, M318F, M320F and M322F Wheeled Excavator and Material Handler Machine Systems Blade Linkage - Remove and Install
307E2 Mini Hydraulic Excavator Machine Systems Seat - Assemble
PM310, PM312 and PM313 Cold Planer Machine Systems Check Valve
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0444 - FMI 06
M314F, M316F, M318F, M320F and M322F Wheeled Excavator and Material Handler Machine Systems Fuel Tank - Remove and Install
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System MID 039 - CID 0444 - FMI 03
Technical Analysis 1 (TA1) Visual Inspection for Motor Grader {0372, 1000, 7000, 753T, 7565} Technical Analysis 1 (TA1) Visual Inspection for Motor Grader {0372, 1000, 7000, 753T, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Excavator {0372, 1000, 7000, 753T, 7565} Technical Analysis 1 (TA1) Visual Inspection for Excavator {0372, 1000, 7000, 753T, 7565}
336D2 and 340D2 Excavators Machine System Mounting Bracket
336D2 and 340D2 Excavators Machine System Hydraulic Tank Mounting
336D2 and 340D2 Excavators Machine System Fuel Tank and Mounting
Custom Parts Information for 308E2 CR Mini Hydraulic Excavators {7000} Custom Parts Information for 308E2 CR Mini Hydraulic Excavators {7000}
316F Excavator Machine Systems Electronic Control (Machine System)
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
M314F and M316F Wheeled Excavators Hydraulic System Margin Pressure - Test and Adjust
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Housing (Front) - Remove and Install
316F Excavator Machine Systems Electronic Control (Pilot System)
316F Excavator Machine Systems Electronic Control (Main Pump System)
316F Excavator Machine Systems Electronic Control (Boom System)
Comprehensive List of Electrical Repair and Troubleshooting Information Is Now Available for All CAT Machines {0374, 0709, 1400, 1408, 7490, 7553, 7610} Comprehensive List of Electrical Repair and Troubleshooting Information Is Now Available for All CAT Machines {0374, 0709, 1400, 1408, 7490, 7553, 7610}
336D2 and 340D2 Excavators Machine System Pump Lines
336D2 and 340D2 Excavators Machine System Return Lines
336D2 and 340D2 Excavators Machine System Boom Cylinder Lines