Carburetor Control Linkage - EG3P Governor
Show/hide table
Illustration 1 | g01038798 |
Note: Use the same dimensions and the same adjustment procedures for the right governor and for the left governor.
(1) Throttle shaft and lever
(2) Cross shaft and lever
- Diameter of cross shaft ...
15.735 ± 0.013 mm (0.6195 ± 0.0005 inch)
(3) Cross shaft bearing cage
- Bore in bearings for cross shaft ...
15.88 ± 0.005 mm (0.6252 ± 0.0002 inch)
(4) Reference angle
- Reference angle for the shaft of the carburetor (full open to full closed position) ... 75 degrees
(5) Rod end and nut
- Torque ...
12 ± 4 N·m (9 ± 3 lb ft)
Assemble the rod ends in order to provide equal thread engagement in the rod on both ends.
(6) Upper assembly
- G3508 ...
194.2 ± 1 mm (7.65 ± 0.04 inch) - G3512 ...
194.2 ± 1 mm (7.65 ± 0.04 inch) - G3516 ...
179.8 ± 1 mm (7.08 ± 0.04 inch) - G3512 ...
Adjust the assembly from the shaft of the carburetor to cross shaft to the following length:
(7) Middle assembly
- Adjusted length ...
404 mm (15.9 inch)
(8) Lower assembly
- Adjusted length ...
254 ±1 mm (10.00 ± 0.04 inch)
(9) Angle
Use the following procedure in order to adjust angle (9):
- Hold the governor shaft in the full open position.
- Install the lever at an angle from horizontal to the following value:
Angle ... 5 + 5 degrees
(10) Reference angle
- Reference angle (full open to full closed position) ... 37 degrees
(11) Governor control shaft
Caterpillar Information System:
2001/12/01 New Crankshaft Assemblies Include Counterweights That Are Permanently Bolted To The Crankshafts {1202, 1231}
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0168 - FMI 04
Electronic Modular Control Panel II+ (EMCP II+) Component Location - 3412 PEEC and 3456 Engines
Electronic Modular Control Panel II+ (EMCP II+) Display of Voltage or Current or Power Is Inaccurate
3500B and 3500B High Displacement Generator Set Engines Ether Injection System
Electronic Modular Control Panel II+ (EMCP II+) Display of Voltage or Current Is Zero
3456 Generator Sets Engine Description
3054B Industrial Engine Maintenance Interval Schedule
3456 Generator Sets Model View Illustrations
3034 Marine Engine Manual Stop Procedure
3054, 3054B and 3056 Marine Engines Flywheel Housing - Remove and Install - 3054 and 3054B Engines
G3406 and G3412 Generator Sets Alarms and Shutoffs
G3406 and G3412 Generator Sets Engine Speed/Timing Sensor - Clean/Inspect
Electronic Modular Control Panel II+ (EMCP II+) Engine Does Not Shutdown (for PEEC Engines)
3500B and 3500 Marine Propulsion Engines with EUI Option Plate Locations and Film Locations
SPS342 Skid Mounted Pumper General Hazard Information
SPS342 Skid Mounted Pumper Fire Prevention and Explosion Prevention
3412C Engine Fuel Injection Pump Housing - Assemble
Electronic Modular Control Panel II (EMCP II) GSC CID 0447 - FMI 12 (for EUI Engines)
Electronic Modular Control Panel II (EMCP II) GSC CID 0447 - FMI 12 (for MUI Engines)
3500B Marine Propulsion Engines Product Description
320B, 320B L and 320B N Excavators Engine Starting with Jump Start Cables - If Equipped
G3500 Engines Cylinder Head Valves
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0566 - FMI 07 (for PEEC Engines)