Vibration of the Right Side Access Door During Machine Operation on Certain 336E and 336E H Excavators{7273}
- Excavator:
- 336E (S/N: KED1-UP; YCE1-UP; TEG1-UP; GTJ1-UP; YEP1-UP; CMR1-UP; BZY1-UP)
- 336E H (S/N: RZA1-UP; SSL1-UP)
Introduction
The problem that is identified below does not have a known permanent solution. Until a permanent solution is known, use the solution that is identified below.
Problem
The right side Access door could vibrate during machine operation. The vibration is due to lack of support.
Solution
If vibration is heard from the right side door, an additional support plate can be installed. The following rework procedure creates an additional support plate in order to eliminate the vibration.
Show/hide table
Illustration 1 | g03418141 |
Support plate installed on the machine |
Rework Procedure
- Drill a 14 mm (0.55 inch) diameter hole. Illustrations 2 and 3 show the location of the hole on the side cover.
Show/hide table
Illustration 2 | g03418142 |
Show/hide table
Illustration 3 | g03418146 |
- Fabricate a support plate. Illustration 4 shows the detailed dimensions.
Show/hide table
Illustration 4 | g03418173 |
Caterpillar Information System:
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Engine Oil Pressure
349F and 352F Excavators Sensor Signal (Analog, Passive) - Test
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Fuel Transfer Pump
349F and 352F Excavators Engine Supplement Ignition Coil - Remove and Install - Clean Emissions Module
2013/08/19 An Improved Spill Guard Bucket is Being Used on 938H Wheel Loaders {0679, 6101}
Procedure to Repair Spill Guard on the Bucket Groups for 938H Through 980K Medium Wheel Loaders {0679, 6101} Procedure to Repair Spill Guard on the Bucket Groups for 938H Through 980K Medium Wheel Loaders {0679, 6101}
311F Excavator Machine Systems Blade Hydraulic System
311F Excavator Machine Systems Blade Hydraulic System
C1.7, C1.8 and C2.4 Tier 4 Interim and EU Stage 3A Engines for Caterpillar Built Machines Lifter Group
349F and 352F Excavators Engine Supplement Relay (ARD Nozzle Heater) - Remove and Install - Clean Emissions Module
349F and 352F Excavators Engine Supplement Fuel Manifold - Remove and Install - Clean Emissions Manifold
349F and 352F Excavators Engine Supplement Fuel Transfer Pump - Remove and Install
323F Excavator Specifications
323F Excavator Boom/Stick/Bucket Combinations
323F Excavator Declaration of Conformity
326F, 329F and 330F Excavators Machine Systems Load Control Valve (Boom Cylinder) - Remove and Install
349F and 352F Excavators Battery Disconnect Switch
323F Excavator Capacities (Refill)
326F, 329F and 330F Excavators Machine Systems Load Control Valve (Boom Cylinder) - Disassemble
349F and 352F Excavators Leaving the Machine
M316C Excavator Machine System Main Hydraulic Pump Mounting
M316C Excavator Machine System Main Hydraulic Pump
A New Stem Assembly for Stick 1 is Available for Certain 349E, 349F, and 352F Excavators and Mobile Hydraulic Power Units {5051} A New Stem Assembly for Stick 1 is Available for Certain 349E, 349F, and 352F Excavators and Mobile Hydraulic Power Units {5051}
2014/09/12 An Improved Foot Valve Assembly for the Fuel Transfer Pump is Now Available as a Service Replacement on Certain 300D and 300E Series Excavators and Mobile Hydraulic Power Units {1256}