Engine Wiring Information
接线示意图 会定期修订。 接线原理图将会随线束导线的更新而更换。 对于最新的信息资料,一定要检查示意图 的修订号。 应使用具有最新的修订号的示意图 。
线束导线识别
Caterpillar 使用 11 种固定颜色来识别所有导线。 电路号以 25 mm (1 in) 间隔压印在导线上。 表 1列出了这些导线颜色和颜色代码。
Show/hide table
线束导线的颜色代码     | |||
颜色代码     | 彩色     | 颜色代码     | 彩色     |
BK     | 黑色     | GN     | 绿色     |
BR     | 棕色     | BU     | 蓝色     |
RD     | 红     | PU     | 紫色     |
OR     | 橙色     | GY     | 灰色     |
YL     | 黄     | WH     | 白色     |
    |     | PK     | 粉红色     |
比如,示意图 上的 A701-GY 的导线识别号码表示一根灰色导线,其电路号为 A701。 A701-GY 为标识电源电路的编号。 1 喷油器电磁阀。
原理图上的另一个导线识别号码为导线的尺码。 导线的尺码将会紧随导线颜色之后。 导线尺码或线规被称之为 AWG(美国线规)。 AWG 用于描述导线的直径。
比如,原理图上的代码 150-OR-14 指示 150 号电路的橙色导线是 14 号 AWG 导线。
如果导线的线规没有在导线上列出来,这些导线应是 16 号 AWG。
AWG 号至公制度量换算表
表 2 中所示为用于导线的各种 AWG 号。 还显示了各个 AWG 号的等效公制直径。
Show/hide table
AWG 号的公制等效尺寸     | |||
AWG 号     | 直径(mm)     | AWG 号     | 直径(mm)     |
20     | 0.8     | 14     | 1.6     |
18     | 1.0     | 12     | 2.0     |
16     | 1.3     | 4     | 3.2     |
在配备电子发动机控制系统的机器上进行焊接
需要采用正确的焊接步骤,避免损坏发动机电子控制模块、传感器及相关元件。 应拆下需要进行焊接的部件。 当在配备电子发动机控制系统的机器上进行焊接,又不可能将部件拆下来时,必须遵循下述步骤。 此步骤对电子部件的危害程度最小。
Show/hide table
注意 |
---|
不要将电焊机的地线接至电气部件如电子控制模块(ECM)或传感器上。 不正确的接地方式能对传动系轴承、液压元件、电气部件和其它部件造成损坏。 用焊接机的地线夹子夹住要焊接的组件。 尽可能将夹子置于焊接点附近。 这将有助于减少损坏的可能性。 |
- 关闭发动机。 把钥匙开关转到断开位置。
- 从蓄电池上断开蓄电池负极电缆。 如果安装了蓄电池断路开关,应断开此开关。
- 将焊接接地电缆连接到尽量靠近将要焊接的区域。 可能会因焊接而损坏的部件包括轴承、液压部件和电气/电子部件。
Show/hide table
图 1 | g01100101 |
焊接电流将不会导致任意相关部件损坏。 |
- 保护配线线束,避免焊接碎片和溅落物损坏线束。
- 使用标准焊接方法焊接材料。
Caterpillar Information System:
3512B and 3516B Engines Air Inlet and Exhaust Lines
2001/01/01 New Boost Pressure Sensor For Marine Engines {1917}
3126B Industrial Engines Component Diagram
3054, 3054B and 3056 Marine Engines Installation Guide Sensor Location
G3516B and G3520B Generator Set Engines Crankshaft Main Bearings - Install
3126B Industrial Engine Fuel System Primary Filter/Water Separator - Drain
2000/11/01 A Power Up Time Delay Relay Is Being Added To The Engine Supervisory System {7490}
2000/11/01 Caterpillar Electronic Control Modules and Computer Viruses {1901, 7620}
2000/11/01 New Engine Software FLASH Files Are Now Available {7620}
2000/11/01 Caterpillar Electronic Control Modules and Computer Viruses {1901, 7620}
C9 Urban Transit Bus Engine ECM Memory - Test
3126B and 3126E On-highway Engines Factory Passwords
3304B-XQ125 Rental Generator Set Model View Illustrations
3126B Industrial Engine Refill Capacities
3304B-XQ125 Rental Generator Set Engine Description
3126B Industrial Engines Electrical Connectors and Functions
C7 Engines for Combat and Tactical Vehicles Cruise Control Switch Circuit - Test
3054, 3054B and 3056 Marine Engines Installation Guide Engine Control
G3516B and G3520B Generator Set Engines Flywheel Housing - Remove
G3516B and G3520B Generator Set Engines Flywheel Housing - Install
Installation Instructions for Turbochargers {1052} Installation Instructions for Turbochargers {1052}
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Acronyms
C-10, C-12, C-15 and C-16 Industrial Engines Battery
Marine Monitoring System II System Power