Swivel - Remove
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | FT-2674 | Vacuum Cap | 1 |
| B | 138-7573 | Link Bracket | 2 |
| C | 1U-7505 | Hydraulic Jack | 1 |
Start By:
- Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Remove cover (1).
Show/hide table
Illustration 2 g01365596 - Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose to Tooling (A). Apply
276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the hydraulic system.Show/hide table
Illustration 3 g01365597 - Disconnect hose assemblies (2), (3), and (4). Remove support (5).
Show/hide table
Illustration 4 g01365598 - Attach Tooling (B) and a suitable lifting device to swivel (10). The weight of swivel (10) is approximately
45 kg (95 lb) . Remove bolts (7) and retainer (9). Remove clamp (8) and boot (6).Show/hide table
Illustration 5 g01365599 Note: The weight of guards (12) can increase due to debris on top of guards (12).
- Position Tooling (C) under guards (12). Remove bolts (11) and guards (12). The weight of each guard (12) is approximately
25 kg (55 lb) .Show/hide table
Illustration 6 g01365602 - Disconnect hose assemblies (16). Disconnect fitting (17). Disconnect hose assemblies (13). Remove fittings (15). Remove bolts (14). Remove swivel (10).
Show/hide table
| |
| Illustration 1 | g01365595 |
Caterpillar Information System:
325D Material Handler Machine Systems Stick Bearings and Seals - Install - Work Tool End
325D Material Handler Machine Systems Stick Bearings and Seals - Remove - Work Tool End
330D Excavator Machine Systems Stick Cylinder - Remove and Install
325D Material Handler Machine Systems Stick Bearings and Seals - Install - Boom End
325D Material Handler Machine Systems Stick Bearings and Seals - Remove - Boom End
321D LCR Excavator Receiver Dryer (Refrigerant) - Replace
325C MHPU Mobile Hydraulic Power Unit Engine Oil and Filter - Change
2007/09/03 New Buckets are Available for Certain Mini Hydraulic Excavators {6101, 6503}
323D MHPU Mobile Hydraulic Power Unit Machine System Specifications Air Conditioner Lines
320D Excavator Leaving the Machine
320D Excavator Additional Messages
320D Excavator Alternate Exit
325D Material Handler Machine Systems Swivel - Install
325D Material Handler Machine Systems Swing Gear and Bearing - Remove
325D Material Handler Machine Systems Swing Gear and Bearing - Install
330D Excavator Machine Systems Sprocket - Remove and Install
321D LCR Excavator Engine Oil and Filter - Change
321D LCR Excavator Additional Messages
M313D, M315D, M316D, M318D and M322D Excavators and M316D MHPU Mobile Hydraulic Power Unit Electronic System Automatic Lubrication Function
325D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Specifications - 325D and 329D Ditch Cleaner
3176C, 3406E and 3456 Industrial Engines Exhaust System Contains Oil
330D Excavator Forest Machine C9 Engine Supplement Refrigerant Condenser and Fan Motor - Remove and Install
2007/04/23 Repair Procedure for Damaged Spillguards on Wheel Loader Buckets {6101, 6102, 7000}
2007/04/16 An Improved Hose Routing Helps Prevent Damage to Hoses {5057}