Final Drive - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-2420     | 变速箱修复台     | 1     |
B     | 138-7575     | 连杆支架     | 3     |
C     | 138-7576     | 连杆支架     | 2     |
D     | 132-8119     | 液压扳手     | 1     |
132-8223 | 液压泵和马达总成     | 1     | |
9U-7418 | 六角头套筒     | 1     | |
E     | 176-6536     | 顶出螺栓     | 2     |
开始:
- 拆下终传动。 请参阅拆解和组装, "终传动 - 拆卸"。
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。 污染物或污垢可能会损坏精密部件。 拆解步骤应在清洁的工作面上进行。 务必盖上部件并采取适当保护措施。
- 将终传动 (1) 紧固到工具 (A) 上。 为便于组装,在终传动 (1) 区域标出对准标记。 所有零件必须重新安装在其原来的位置。 终传动 (1) 的重量约为 1020 kg (2250 lb)。
Show/hide table
图 1 | g01284546 |
- 从壳体盖 (3) 上拆下套筒调整螺钉 (2) 。
Show/hide table
图 2 | g01284563 |
- 将工具 (B) 和适当的起吊设备固定到壳体盖 (3) 上。
Show/hide table
图 3 | g01284577 |
- 拆下螺栓 (4) 和垫圈。 使用软面锤敲碎壳体盖 (3) 和齿圈之间的密封件。 拆下壳体盖 (3) 。 壳体盖 (3) 的重量约为 95 kg (210 lb)。
- 从壳体盖 (3) 上拆下隔套 (5) 和垫片。
Show/hide table
图 4 | g01284579 |
- 从壳体盖 (3) 上拆下内六角头螺栓 (6) 和齿圈 (7) 。
- 拆下太阳齿轮 (8) 。
Show/hide table
图 5 | g01284589 |
- 采用工具 (B) 和适当的起吊设备拆下托架组件 (9) 。 托架组件 (9) 的重量大约为 43 kg (95 lb)。
Show/hide table
图 6 | g01284593 |
- 拆下挡圈 (10) 、隔套 (11) 和太阳齿轮 (12) 。
Show/hide table
图 7 | g01284596 |
- 将弹簧销 (14) 打入行星齿轮轴 (15) 中。 拆下行星齿轮轴 (15) 和行星齿轮组件 (13) 。
Show/hide table
图 8 | g01284599 |
- 将垫圈 (16) 和轴承 (17) 从行星齿轮 (18) 上拆下。 从行星齿轮轴 (15) 上拆下弹簧销 (14) 。
Show/hide table
图 9 | g01284603 |
- 对其余的行星齿轮组件重复步骤 10 和 11。
- 采用工具 (B) 和适当的起吊设备以拆下托架组件 (19) 。 托架组件 (19) 的重量大约为 95 kg (210 lb)。
Show/hide table
图 10 | g01284605 |
- 拆下挡圈 (20) 、隔套 (21) 和太阳齿轮组件 (22) 。
Show/hide table
图 11 | g01284609 |
- 将弹簧销 (23) 打入行星齿轮轴 (25) 。 拆下行星齿轮轴 (25) 和行星齿轮组件 (24) 。
Show/hide table
图 12 | g01284612 |
- 将垫圈 (28) 和轴承 (27) 从行星齿轮 (26) 上拆下。 从行星齿轮轴 (25) 上拆下弹簧销 (23) 。
Show/hide table
图 13 | g01284616 |
- 对其余的行星齿轮组件重复步骤 15 和 16。
- 拆下隔套 (30) 。 采用工具 (B) 和适当的起吊设备拆下托架组件 (29) 。 托架组件 (29) 的重量约为 132 kg (290 lb)。
Show/hide table
图 14 | g01284622 |
- 将弹簧销 (32) 打入行星齿轮轴 (33) 。 拆下行星齿轮轴 (33) 和行星齿轮组件 (31) 。
Show/hide table
图 15 | g01284632 |
- 将垫圈 (34) 和 (38) 以及轴承 (35) 和 (37) 从行星齿轮 (36) 上拆下。 从行星齿轮轴 (33) 上拆下弹簧销 (32) 。
Show/hide table
图 16 | g01284637 |
- 对其余的行星齿轮组件重复步骤 19 和 20。
- 利用工具 (B) 和适当的起吊设备将齿圈 (39) 从壳体 (40) 上拆下。 齿圈 (39) 的重量约为 155 kg (340 lb)。
Show/hide table
图 17 | g01284647 |
- 将 O 形密封圈 (41) 从壳体 (40) 上拆下。
Show/hide table
图 18 | g01284657 |
- 将适当的支座放在马达壳体 (42) 下方,以拆下马达壳体 (42) 。
Show/hide table
图 19 | g01284704 |
- 使用工具 (D) 从连接齿轮 (44) 上拆下螺栓 (43) 。
注: 必须修改一部分工具 (D) 。 六角头套筒 上的切割长度 (X) 为 14.0 mm (0.55 in)。
Show/hide table
图 20 | g01284709 |
Show/hide table
图 21 | g00865969 |
- 如图所示,将工具 (E) 安装到连接齿轮 (44) 上。 均匀地拧紧工具 (E) 以松开连接齿轮 (44) 。 从马达壳体 (42) 上拆下连接齿轮 (44) 。
Show/hide table
图 22 | g01284713 |
- 从马达壳体 (42) 上拆下垫片 (45) 。
Show/hide table
图 23 | g01284718 |
- 拆下螺栓 (46) 。 采用工具 (C) 和适当的起吊设备以从马达壳体 (42) 分离壳体 (40) 。 马达壳体 (42) 将安置在适当的支座上。 壳体 (40) 的重量约为 250 kg (550 lb)。
Show/hide table
图 24 | g01284723 |
- 从壳体 (40) 上拆下轴承内圈 (47) 。
Show/hide table
图 25 | g01284734 |
- 使用工具 (C) 和适当的起吊设备将壳体 (40) 翻转到另一侧。 壳体 (40) 的重量约为 250 kg (550 lb)。
Show/hide table
图 26 | g01284738 |
- 从壳体 (40) 上拆下 Duo-Cone 密封件 (48) 、轴承外圈 (49) 和 (50) 。
- 如有必要,从马达壳体 (42) 上拆下销 (51) 。
Show/hide table
图 27 | g01284743 |
- 从马达壳体 (42) 上拆下轴承内圈 (52) 。
- 从马达壳体 (42) 上拆下 Duo-Cone 密封件 (53) 。
Caterpillar Information System:
390D Excavator Machine Systems Final Drive - Install
390D Excavator Machine Systems Final Drive - Remove
324D and 325D Forest Machines Machine Systems Main Control Valve - Install
3176C Engines for Caterpillar Built Machines Sensors and Electrical Connectors
Field Service for Positive Pin Retention 2 (PPR 2) {4169, 4170, 4171, 4174, 4175, 4180} Field Service for Positive Pin Retention 2 (PPR 2) {4169, 4170, 4171, 4174, 4175, 4180}
324D and 325D Forest Machines Machine Systems Drift Reduction Valve (Boom) - Install
324D and 325D Forest Machines Machine Systems Drift Reduction Valve (Stick) - Install
324D and 325D Forest Machines Machine Systems Main Control Valve - Remove
308C CR, 314C CR and 321C CR Excavators Air Conditioning and Heating Control Panel
GLL52, GLL52B, GLL55, GLL55B, GLL60 and GLL60B Hydraulic Excavator Forestry Grapples Grapple Tong and Bearing - Install
324D and 325D Forest Machines Machine Systems Drift Reduction Valve (Stick) - Remove
324D and 325D Forest Machines Machine Systems Drift Reduction Valve (Boom) - Remove
330D Forest Machine Hydraulic System Operational Checks
330D Forest Machine Hydraulic System Main Hydraulic System
330D Forest Machine Hydraulic System Main Hydraulic System
H35D S, H45D S, H55D S and H65D S Hydraulic Hammers Hydraulic Hammer
308C CR, 314C CR and 321C CR Excavators Air Conditioning and Heating Air Conditioning System Troubleshooting - Guide for Sensors
330D Forest Machine Hydraulic System Engine Performance - Test - Engine Speed
324D and 325D Forest Machines Machine Systems Swing Cushion Valve - Remove
H35D S, H45D S, H55D S and H65D S Hydraulic Hammers Tools (Hammer)
330D Forest Machine Hydraulic System Travel on Level Ground - Test - Optional Test
324D and 325D Forest Machines Machine Systems Swing Cushion Valve - Install
330D Forest Machine Hydraulic System Travel on Level Ground - Test
2006/11/20 The Seal for the Hydraulic Filter Is Improved and a Modified Plate Improves the Breathing of the Hydraulic Tank {5056, 5068}