Travel on Level Ground - Test - Optional Test
Note: When the procedure for the Travel On Level Ground cannot be performed, this test may be used as a substitute.
Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for the engine speed that was used for this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.
Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".
Show/hide table
Required Tools     | |
---|---|
Description     | Qty     |
Stopwatch     | 1     |
Show/hide table
Illustration 1 | g00297292 |
- Start the engine.
- Position the machine on level ground.
- Increase the hydraulic oil temperature to 55° ± 5°C (131° ± 9°F).
- Raise a track off the ground. Refer to Illustration 1.
- Put a mark on a shoe of the raised track.
- Place the machine controls at the following settings: Engine speed dial "10" and AEC switch OFF.
- Place the travel speed control switch in HIGH position.
- Move the travel lever of the raised track to full travel position.
- Measure the time that is required for the raised track to make three complete revolutions. Measure the time that is required in each direction.
- Place the travel speed control switch in the LOW position and repeat Steps 8 through 9.
Show/hide table
320D RR Time For Three Revolutions (time in seconds)     | ||||
---|---|---|---|---|
Travel Speed     | New     | Rebuild     | Service Limit     | |
HIGH     | Forward     | 17.0 or less     | 18.0 or less     | 19.0 or less     |
Reverse | ||||
LOW     | Forward     | 27.5 or less     | 28.5 or less     | 30.5 or less     |
Reverse |
Show/hide table
320D LRR Time For Three Revolutions (time in seconds)     | ||||
---|---|---|---|---|
Travel Speed     | New     | Rebuild     | Service Limit     | |
HIGH     | Forward     | 18.5 or less     | 19.6 or less     | 20.7 or less     |
Reverse | ||||
LOW     | Forward     | 30.0 or less     | 31.0 or less     | 38.0 or less     |
Reverse |
Caterpillar Information System:
2005/09/26 A New Fuel Lift Pump is Now Available {1256, 1258}
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power Unit Machine Systems Pilot Valve (Joystick) - Assemble
320D and 323D Excavators Hydraulic System Travel on Level Ground - Test
320D RR Excavator and 320D RR Forest Machine Hydraulic System Operational Checks
PP120 and PH126 Power Pack and Hammer Hydraulic Hand Control - Assemble
PP120 and PH126 Power Pack and Hammer Hydraulic Hand Control - Disassemble
M325D MH Material Handler Air Conditioning and Heating Control
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power Unit Machine Systems Pilot Valve (Joystick) - Disassemble
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Scavenge Pump - Remove
304C CR and 305C CR Mini Hydraulic Excavators Hydraulic System Specifications
304C CR and 305C CR Mini Hydraulic Excavators Hydraulic System Relief Valve (Swing) - Test and Adjust
305E CR and 305.5E CR Mini Hydraulic Excavators Hydraulic System Relief Valve (Line) - Test and Adjust
320D and 323D Excavators Hydraulic System Swing Speed and Overswing on Level Ground - Check
320D and 323D Excavators Hydraulic System Swing Speed and Swing Drift on a Slope - Check
3500 and 3500B High Displacement Engines for Caterpillar Built Machines Engine Oil Scavenge Pump - Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Relief Valve (Pilot) - Remove
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System General Information
320D RR Excavator and 320D RR Forest Machine Hydraulic System Cylinder Drift - Check - Loaded Bucket
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System System Operation
320D and 323D Excavators Hydraulic System Cylinder Speed - Check
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Relief Valve (Pilot) - Install
320D, 321D, 323D, 324D, 325D, 326D, 328D, 329D, 330D, 336D, 336D2, 340D and 340D2 Excavators, 324D Forest Machine and 323D MHPU, 324D MHPU, 325D MHPU, 329D MHPU, 330D MHPU and 336D MHPU Mobile Hydraulic Power Units Machine Electronic Control System Diagnostic Operation
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power Unit C9 Engine Supplement Refrigerant Compressor - Remove and Install
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power Unit Machine Systems Manual Valve (Auxiliary Shutoff) - Remove