Air Cleaner - Remove and Install
Removal Procedure
- Open the left, rear door on the machine.
- Release two clips (1), and remove cover assembly (2) .
Show/hide table
 | |
| Illustration 1 | g00811622 |
- Remove primary element (3) .
Show/hide table
 | |
| Illustration 2 | g00811623 |
- Remove secondary element (4) .
Show/hide table
 | |
| Illustration 3 | g00811624 |
- Loosen two hose clamps (5), and remove hose (6). Disconnect two electrical connectors (7), and cut the tie strap for the wiring harness.
Show/hide table
 | |
| Illustration 4 | g00811625 |
- Loosen clamp (8), and remove bolts (9). Remove the air cleaner housing.
Show/hide table
 | |
| Illustration 5 | g00811629 |
- Remove seal (10) from the cover assembly.
Show/hide table
 | |
| Illustration 6 | g00811630 |
Installation Procedure
Note: Check the seal and hoses for wear and for damage. Replace the components, if necessary.
- Install seal (10) in the cover assembly.
Show/hide table
| | |
| Illustration 7 | g00811630 |
- Place the air cleaner housing in position on the machine. Install bolts (9) in order to fasten the air cleaner housing to the machine. Tighten clamp (8) .
Show/hide table
| | |
| Illustration 8 | g00811629 |
- Connect hose (6) to the air cleaner housing. Tighten clamp (5). Attach electrical connectors (7) .
Show/hide table
| | |
| Illustration 9 | g00811625 |
- Install secondary element (4) .
Show/hide table
| | |
| Illustration 10 | g00811624 |
- Install primary element (3) .
Show/hide table
| | |
| Illustration 11 | g00811623 |
- Install cover assembly (2), and engage clips (1) .
Show/hide table
| | |
| Illustration 12 | g00811622 |
- Close the left, rear door.
Caterpillar Information System:
3064 and 3066 Engines for Caterpillar Built Machines Fuel System - Prime
325C and 325C L Excavator Bucket Linkage (C Family) - Lubricate
305.5 Mini Hydraulic Excavator Machine System Specifications Pilot Valve - Auxiliary
3500B Engines for 5130B and 5230B Excavators MID 036 - CID 0542 - FMI 04 Unfiltered Engine Oil Pressure short to ground
3064 and 3066 Engines for Caterpillar Built Machines High Idle RPM - Adjust
HDB Series and M1 Series Heavy Duty Brushless Alternators General Information
2001/09/04 A New Gasket For The Radiator Is Available {1353}
3064 and 3066 Engines for Caterpillar Built Machines Low Idle RPM - Adjust
2001/07/30 Special Instruction, REHS1040 , "Procedure for the Repair of Compensator Valves in the Main Hydraulic Control Valve" is Available {5051}
3064 and 3066 Engines for Caterpillar Built Machines Governor - Adjust - In-line Fuel Pump
325C and 325C L Excavator Hydraulic System Oil Filter (Pilot) - Replace
305 CR Mini Hydraulic Excavator Machine System Specifications Blade Mounting
3064 and 3066 Engines for Caterpillar Built Machines Fuel System Pressure - Test
3500B Engines for 5130B and 5230B Excavators MID 036 - CID 0547 - FMI 05 Ether Injection Lamp open circuit
3064 and 3066 Engines for Caterpillar Built Machines Air Inlet and Exhaust System - Inspect
3064 and 3066 Engines for Caterpillar Built Machines Turbocharger - Inspect
3500B Engines for 5130B and 5230B Excavators MID 036 - CID 0547 - FMI 06 Ether Injection Lamp short to ground
303.5C CR and 303C CR Mini Hydraulic Excavators Machine System Specifications Joystick Control
HDB Series and M1 Series Heavy Duty Brushless Alternators Normal Operation
3064 and 3066 Engines for Caterpillar Built Machines Exhaust Temperature - Test
3064 and 3066 Engines for Caterpillar Built Machines Engine Crankcase Pressure (Blowby) - Test
3064 and 3066 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
3064 and 3066 Engines for Caterpillar Built Machines Valve Guide - Inspect
3500B Engines for 5130B and 5230B Excavators MID 036 - CID 0580 - FMI 03 Power Shift Pres Sensor open/short to +batt