Fuel Injection Nozzles - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 1U-7600     | 滑锤拉拔器     | 1     |
B     | 9U-6278     | 适配器     | 1     |
开始:
- 拆下燃油喷油管。 请参阅拆解和组装, "燃油喷油管路 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下将卡箍 (2) 固定到缸盖组件上的螺栓 (1) 和垫圈。
Show/hide table
图 1 | g00652319 |
- 拆下将喷油嘴 (3) 固定到缸盖组件内的卡箍 (2) 。
注: 立即在所有开孔上加装保护盖或螺塞,以防止燃油系统污染。
注: 标记卡箍,以便于随后的安装。
- 将工具 (B) (未显示)安装到喷油嘴上。
注: 工具 (B) 安装在燃油喷油管的接头 (4) 上。
- 将工具 (A) (未显示)连接到工具 (B) 后缓慢地拆下喷油嘴 (3) 。
注: 将工具 (A) 的中心线与喷油嘴 (3) 延长的中心线对齐。 此步骤将有助于避免出现可能造成喷油嘴弯曲或断裂的喷油嘴变形。
- 将底座垫圈从喷油嘴上拆下。
Caterpillar Information System:
5230B Excavator Hydraulic System Caterpillar Underspeed System - Calibrate
5230 Excavator Hydraulic System Power Shift Pressure - Check
Flash Procedure For The Software Update Of The EMCP II+ With Generator Set Control+{4490} Flash Procedure For The Software Update Of The EMCP II+ With Generator Set Control+{4490}
W330B Material Handler Leaving the Machine
C-9 Engines for Caterpillar Built Machines Water Temperature Regulator
307B Excavator Blade Control
3064 and 3066 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
307B Excavator Engine Speed Control
3126B Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
W330B Material Handler Safety Messages
3064 and 3066 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seals - Remove and Install
307B Excavator Heating and Air Conditioning Control - If Equipped
318B and 318B LN Excavator Lifting Capacities - 318C L with VA Boom
5230 Excavator Hydraulic System M1 Port Pressure - Check
W330B Material Handler Material Handler Operation
3114, 3116 and 3126 MUI Engine Governors Prepare Calibration Bench for Test Procedure
3064 and 3066 Engines for Caterpillar Built Machines Fuel Injection Nozzles - Install
W330B Material Handler Engine Stopping
W330B Material Handler Shipping the Machine
C-9 Engines for Caterpillar Built Machines Cylinder Block
W330B Material Handler Cab Tilting
3064 and 3066 Engines for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install
W330B Material Handler Boom Base Pins - Lubricate
307B Excavator Machine Systems Final Drive and Travel Motor - Assemble - Single Speed