Crankshaft Front Seal - Install
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 9U-6180 | 前油封安装工具 | 1 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁所有配对零件的表面。 在新曲轴前密封上涂抹一薄层洁净的发动机机油。
Show/hide table
 | |
| 图 1 | g00612743 |
- 利用工具 (A) 将新曲轴前密封 (1) 安装到前壳体内。
- 拆下工具 (A) ，并检查曲轴前密封 (1) 是否安装正确。
- 在将接触新曲轴前密封的曲轴皮带轮上涂抹洁净的发动机油。
End By: 安装曲轴皮带轮。 请参阅 拆解和组装, "曲轴皮带轮 - 拆卸和安装"。
Caterpillar Information System:
365B and 365B Series II Excavators Supplement for 3196 Engine Air Cleaner - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Crankshaft - Install
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Track Adjuster - Install
SR500 Generators General Maintenance Information
312B-5090B, M325B, W330B and W345B Series II Excavators Air Conditioning and Heating Speed Control - Test
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0100 - FMI 04 Engine Oil Pressure short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0100 - FMI 03 Engine Oil Pressure open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0100 - FMI 13 Engine Oil Pressure calibration required
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0542 - FMI 13 Unfiltered Engine Oil Pressure cal required
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0542 - FMI 04 Unfiltered Engine Oil Pressure short to ground
365B and 365B Series II Excavators Supplement for 3196 Engine Engine Oil Filter and Oil Filter Base - Remove and Install
365B and 365B Series II Excavators Supplement for 3196 Engine Electric Starting Motor - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
3064 and 3066 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
3126B Engine for Caterpillar Built Machines Main Bearing Journal
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Main Hydraulic Pump - Disassemble
318B Excavator Machine System Specifications Piston Pump (Main)
302.5 Mini Hydraulic Excavator Hydraulic System Relief Valve (Line)
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Housing (Front) - Remove
3304B and 3306B Engines for Caterpillar Built Machines Engine Balancer Shaft Bearings - Remove and Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Housing (Front) - Install
318B Excavator Machine System Specifications Swing Motor
301.5, 301.6 and 301.8 Mini Hydraulic Excavators Hydraulic System Pilot Hydraulic System
322B, 322B L, 325B and 325B L Excavators Maintenance Interval Schedule