Crankshaft - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 6V-9120     | 套筒 (1)     | 1     |
B     | 8T-5096     | 千分表     | 1     |
Show/hide table
( 1 ) | 工具 (A) 为 46 mm 套筒。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 如果止推垫圈已拆下,则将止推垫圈 (11) 安装到曲轴的后端面上,使机油槽向外。
Show/hide table
图 1 | g00604687 |
- 将曲轴主轴承 (10) 的上半部分定位到缸体中。 将曲轴主轴承的下半部分放在曲轴主轴承盖中。 安装轴承,使主轴承凸舌处于正确的位置。 用洁净的发动机机油润滑轴承。
- 用洁净的发动机机油润滑曲轴轴颈。 将适当的起吊设备和吊带固定到曲轴 (9) 上。 3064 发动机曲轴的重量为 84 kg (185 lb)。 3066 发动机曲轴的重量为 99 kg (220 lb)。 将曲轴 (9) 定位到曲轴主轴承的上半体上。
注: 小心不要损坏曲轴的抛光面。
Show/hide table
图 2 | g00604584 |
- 将主轴承安装到主轴承盖 (8) 内。 安装轴承,使主轴承凸舌处于正确的位置。 用洁净的发动机机油润滑轴承。
Show/hide table
图 3 | g00604582 |
- 将止推垫圈放到后侧主轴承盖上。 将后侧主轴承盖和两个密封安装到缸体的后轴颈上。
- 安装曲轴主轴承盖 (8) 。 在主轴承盖螺栓的螺纹上涂上干净的机油。 安装主轴承盖螺栓 (7) 。 均匀拧紧螺栓至扭矩为 137 ± 5 N·m (101 ± 4 lb ft)。
注: 确保曲轴主轴承盖安装到原位。
- 割掉缸体后轴颈上两密封多余的长度。
- 利用工具 (B) 检查曲轴的轴向间隙。 轴向间隙必须为 0.100 至 0.264 mm (0.0039 至 0.0104 in)。 关于曲轴轴向间隙的更多信息,请参阅测试和调整单元, "缸体基体"。
Show/hide table
图 4 | g00604753 |
- 在连杆轴承和连杆轴颈上涂抹一薄层洁净的发动机机油。 将连杆安装到连杆轴颈上。
Show/hide table
图 5 | g00604552 |
- 将连杆轴承的下半部分安装到相应的连杆盖上,然后安装连杆盖 (6) 。
注: 将连杆轴承背面的凸舌对准连杆盖上的凸舌槽。
安装活塞和连杆。 请参阅拆解和组装, "活塞和连杆 - 安装"。
- 将曲轴完全旋转两圈,以检查曲轴的自由旋转情况。 利用工具 (A) 在曲轴皮带轮螺母 (4) 上转动曲轴。
Show/hide table
图 6 | g00604549 |
- 将 O 形密封圈 (3) 安装到机油供应管 (2) 上。
Show/hide table
图 7 | g00604637 |
- 定位机油供应管 (2) 。 通过安装两条螺栓 (1) 将机油供应管固定到缸体上。
Show/hide table
图 8 | g00604627 |
End By:
- 安装发动机油底壳。 请参阅 拆解和组装, "发动机油底壳 - 拆卸和安装"。
- 安装飞轮壳体。 请参阅 拆解和组装, "飞轮壳体 - 拆卸和安装"。
- 安装前壳体。 请参阅 拆解和组装, "壳体(前) - 安装"。
- 如果曲轴耐磨衬套已拆下,则安装曲轴后密封。 请参阅 拆解和组装, "曲轴后密封 - 安装"。
Caterpillar Information System:
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Track Adjuster - Install
SR500 Generators General Maintenance Information
312B-5090B, M325B, W330B and W345B Series II Excavators Air Conditioning and Heating Speed Control - Test
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0100 - FMI 04 Engine Oil Pressure short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0100 - FMI 03 Engine Oil Pressure open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0100 - FMI 13 Engine Oil Pressure calibration required
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0542 - FMI 13 Unfiltered Engine Oil Pressure cal required
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0542 - FMI 04 Unfiltered Engine Oil Pressure short to ground
365B and 365B Series II Excavators Supplement for 3196 Engine Engine Oil Filter and Oil Filter Base - Remove and Install
365B and 365B Series II Excavators Supplement for 3196 Engine Electric Starting Motor - Remove and Install
365B and 365B Series II Excavators Supplement for 3196 Engine Engine - Install
365B and 365B Series II Excavators Supplement for 3196 Engine Engine - Remove
365B and 365B Series II Excavators Supplement for 3196 Engine Air Cleaner - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Crankshaft Front Seal - Install
3064 and 3066 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
3064 and 3066 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
3126B Engine for Caterpillar Built Machines Main Bearing Journal
365B, 365B Series II, 365BL and 365BL Series II Excavators Machine Systems Main Hydraulic Pump - Disassemble
318B Excavator Machine System Specifications Piston Pump (Main)
302.5 Mini Hydraulic Excavator Hydraulic System Relief Valve (Line)
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Housing (Front) - Remove
3304B and 3306B Engines for Caterpillar Built Machines Engine Balancer Shaft Bearings - Remove and Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Housing (Front) - Install
318B Excavator Machine System Specifications Swing Motor