Housing (Front) - Install
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean old gasket material (11) from the contact surface of front housing (8) and the timing gear plate. Install a new gasket.
Note: Check the condition of the gaskets and the O-ring seals. If the gaskets or the O-ring seals are damaged or worn, use new parts for replacement.
Show/hide table
Illustration 1 | g00529392 |
- Install bearing (12), if equipped. If the bearing is worn or damaged, use a new part for replacement.
- Install O-ring seal (13) onto cover (9), if equipped.
- Install a new crankshaft front seal (10), if the crankshaft front seal was removed. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Install".
Show/hide table
Illustration 2 | g00529391 |
- If equipped, install camshaft gear cover (9) onto front housing (8) .
- Install front housing (8) .
Show/hide table
Illustration 3 | g00529390 |
- Install bolts (7) in order to fasten front housing (8) onto the cylinder block.
- Install the washers and six bolts (6) in order to secure front housing (8) onto engine oil pan.
- Install cover (5) for fuel injection pump gear.
- Install the washers and five bolts (4) in order to secure cover (5) for fuel injection pump gear onto front housing (8) .
- If equipped, install the washers and bolts (3) in order to secure camshaft gear cover (9) onto front housing (8) .
- Install fan pulley (2) .
Show/hide table
Illustration 4 | g00560210 |
- Install the washers and four bolts (1) in order to secure fan pulley (2) onto the water pump.
End By:
- Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove and Install".
- Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and Install".
Caterpillar Information System:
3046 Engine For Caterpillar Built Machines Housing (Front) - Remove
317B Excavator Machine System and Attachment Specifications Stick - Long
3064 and 3066 Engines for Caterpillar Built Machines Flywheel
317B Excavator Machine System and Attachment Specifications Lines (Boom)
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Short with Medium Pressure
320B Excavator Machine System Specifications Remote Fuel Control - Shutoff and Drain
320B Excavator Machine System Specifications Stick - 1900 mm (74.8 inch)
322B, 322B L, 325B and 325B L Excavators V-Belts - Inspect/Adjust/Replace
3064 and 3066 Engines for Caterpillar Built Machines Cylinder Block
322B, 322B L, 325B and 325B L Excavators Fuses - Replace
320B Excavator Machine System Specifications Stick - 1900 mm (74.8 inch)
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Medium with Quick Coupler
M318 Excavator Hydraulic System Relief Valve (Medium Pressure Function) - Test and Adjust
3046 Engine For Caterpillar Built Machines Gear Group (Front) - Remove - Idler Gear Only
3064 and 3066 Engines for Caterpillar Built Machines Exhaust Manifold
317B Excavator Machine System and Attachment Specifications Lines (Boom)
3046 Engine For Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Fuel Injection Nozzles
3064 and 3066 Engines for Caterpillar Built Machines Fuel Injection Lines
Installation of New Cleaner Group and Precleaner{1051, 1055} Installation of New Cleaner Group and Precleaner{1051, 1055}
3064 and 3066 Engines for Caterpillar Built Machines Fuel Injection Pump
3046 Engine For Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
3064 and 3066 Engines for Caterpillar Built Machines Turbocharger
3064 and 3066 Engines for Caterpillar Built Machines Engine Oil Pan