Housing (Front) - Remove
Removal Procedure
Start By:
- Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and Install".
- Remove the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Remove four bolts (1) and the washers from fan pulley (2) .
Show/hide table
Illustration 1 | g00560210 |
- Remove fan pulley (2) .
- If equipped, remove bolts (3) and the washers from front housing (8) .
Show/hide table
Illustration 2 | g00529390 |
- Remove five bolts (4) and the washers from cover (5) for the fuel injection pump gear.
- Remove cover (5) for the engine oil pump.
- Remove six bolts (6) and the washers that secure the engine oil pan to the front housing.
- Remove bolts (7) that secure front housing (8) to the cylinder block.
- Remove front housing (8) .
- If equipped, remove cover (9) for the camshaft gear.
Show/hide table
Illustration 3 | g00529391 |
- Check the condition of crankshaft front seal (10). If the crankshaft front seal is worn or damaged, use a new part for replacement. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Remove" for removal of the crankshaft front seal .
- Remove bearing (12), if equipped. If the bearing is worn or damaged, use a new part for replacement.
Show/hide table
Illustration 4 | g00529392 |
- Clean old gasket material (11) from the contact surface of front housing (8) and the timing gear plate.
Caterpillar Information System:
317B Excavator Machine System and Attachment Specifications Stick - Long
3064 and 3066 Engines for Caterpillar Built Machines Flywheel
317B Excavator Machine System and Attachment Specifications Lines (Boom)
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Short with Medium Pressure
320B Excavator Machine System Specifications Remote Fuel Control - Shutoff and Drain
320B Excavator Machine System Specifications Stick - 1900 mm (74.8 inch)
322B, 322B L, 325B and 325B L Excavators V-Belts - Inspect/Adjust/Replace
3064 and 3066 Engines for Caterpillar Built Machines Cylinder Block
322B, 322B L, 325B and 325B L Excavators Fuses - Replace
320B Excavator Machine System Specifications Stick - 1900 mm (74.8 inch)
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Medium with Quick Coupler
3046 Engine For Caterpillar Built Machines Crankshaft Front Seal - Install
3046 Engine For Caterpillar Built Machines Housing (Front) - Install
M318 Excavator Hydraulic System Relief Valve (Medium Pressure Function) - Test and Adjust
3046 Engine For Caterpillar Built Machines Gear Group (Front) - Remove - Idler Gear Only
3064 and 3066 Engines for Caterpillar Built Machines Exhaust Manifold
317B Excavator Machine System and Attachment Specifications Lines (Boom)
3046 Engine For Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
3064 and 3066 Engines for Caterpillar Built Machines Fuel Injection Nozzles
3064 and 3066 Engines for Caterpillar Built Machines Fuel Injection Lines
Installation of New Cleaner Group and Precleaner{1051, 1055} Installation of New Cleaner Group and Precleaner{1051, 1055}
3064 and 3066 Engines for Caterpillar Built Machines Fuel Injection Pump
3046 Engine For Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
3064 and 3066 Engines for Caterpillar Built Machines Turbocharger