Stick - 1900 mm (74.8 inch)
Show/hide table
Illustration 1 | g00529343 |
Note: All bores must be free of paint. Coat all bores for pins with lubricant.
(1) Lubricate the sealing lip slightly with the lubricant that is being sealed.
(2) 137-2819 Sleeve Bearing
- Quantity ... 2
- Outside diameter ... 106.200 ± 0.013 mm (4.1811 ± .0005 inch)
- Inside diameter ... 90.27 ± 0.02 mm (3.554 ± .001 inch)
- Install the sleeve bearing in the bearing bore. ... 9.5 ± 0.8 mm (.37 ± .03 inch)
- Outside diameter ... 106.200 ± 0.013 mm (4.1811 ± .0005 inch)
(3) 137-2848 Pin Assembly
- Diameter after plating ... 79.85 ± .025 mm (3.144 ± 0.001 inch)
- Minimum thickness for plating ... 0.005 mm (.0002 inch)
- Bore diameter for pin ... 80.037 ± .037 mm (3.1511 ± 0.0015 inch)
- Minimum thickness for plating ... 0.005 mm (.0002 inch)
(4) Torque for bolts ... 460 ± 60 N·m (340 ± 44 lb ft)
(5) Use the necessary shims to adjust the lateral clearance.
- Maximum clearance ... 1.0 mm (.04 inch)
- 133-2425 Shim thickness ... 0.5 mm (.02 inch)
- 093-0083 Shim thickness ... 1.0 mm (.04 inch)
- 7Y-2498 Shim thickness ... 1.6 mm (0.06 inch)
- 093-0115 Shim thickness ... 2.0 mm (.08 inch)
- 133-2425 Shim thickness ... 0.5 mm (.02 inch)
(6) Use the necessary shims to adjust the lateral clearance.
- Maximum clearance ... 1.0 mm (0.04 inch)
- 133-2424 Shim thickness ... 0.5 mm (0.02 inch)
- 093-0086 Shim thickness ... 1.0 mm (.04 inch)
- 7Y-2496 Shim thickness ... 1.6 mm (0.06 inch)
- 093-0118 Shim thickness ... 2.0 mm (.08 inch)
- 133-2424 Shim thickness ... 0.5 mm (0.02 inch)
(7) 134-9037 Pin Assembly
- Diameter after plating ... 69.850 ± .025 mm (2.7500 ± 0.0010 inch)
- Minimum thickness for plating ... 0.005 mm (.0002 inch)
- Bore diameter for pin ... 70.037 ± .037 mm (2.7574 ± 0.0015 inch)
- Minimum thickness for plating ... 0.005 mm (.0002 inch)
(8) 128-9884 Sleeve Bearing
- Quantity ... 2
- Outside diameter ... 95.180 ± .013 mm (3.7472 ± 0.0005 inch)
- Inside diameter ... 80.250 ± .020 mm (3.1594 ± 0.0008 inch)
- Install the sleeve bearing in the bearing bore. ... 7.5 ± 0.8 mm (.30 ± .03 inch)
- Outside diameter ... 95.180 ± .013 mm (3.7472 ± 0.0005 inch)
Note: Assemble the sleeve bearings with the groove in the position that is indicated. The view is shown at 40 ± 5°.
Caterpillar Information System:
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Medium with Quick Coupler
3046 Engine For Caterpillar Built Machines Crankshaft Front Seal - Install
3046 Engine For Caterpillar Built Machines Crankshaft Front Seal - Remove
G3500B Engines Manual Stop Procedure
3046 Engine For Caterpillar Built Machines V-Belts - Remove and Install
317B Excavator Machine System and Attachment Specifications Boom - Pin Group forHA Boom
307B Excavator Machine Systems Main Control Valve - Assemble
307B Excavator Machine Systems Main Control Valve - Disassemble
307B Excavator Machine Systems Main Control Valve - Install
307B Excavator Machine Systems Main Control Valve - Remove
307B Excavator Machine Systems Accumulator (Hydraulic Pilot) - Remove and Install
307B Excavator Machine Systems Relief Valve (Pilot) - Remove and Install
322B, 322B L, 325B and 325B L Excavators Fuses - Replace
3064 and 3066 Engines for Caterpillar Built Machines Cylinder Block
322B, 322B L, 325B and 325B L Excavators V-Belts - Inspect/Adjust/Replace
320B Excavator Machine System Specifications Stick - 1900 mm (74.8 inch)
320B Excavator Machine System Specifications Remote Fuel Control - Shutoff and Drain
317B Excavator Machine System and Attachment Specifications Lines (Stick) - Short with Medium Pressure
317B Excavator Machine System and Attachment Specifications Lines (Boom)
3064 and 3066 Engines for Caterpillar Built Machines Flywheel
317B Excavator Machine System and Attachment Specifications Stick - Long
3046 Engine For Caterpillar Built Machines Housing (Front) - Remove
3046 Engine For Caterpillar Built Machines Housing (Front) - Install
M318 Excavator Hydraulic System Relief Valve (Medium Pressure Function) - Test and Adjust