Fuel Transfer Pump - Assemble
Show/hide table
需要的工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1P-0510 | 驱动器总成 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 用清洁的发动机机油涂在支架 (16)的唇形密封件上。
- 使用工具 (A)在支架 (16)中安装内唇形密封 (18)和外唇形密封 (17)。
注: 如果支架 (16)上的轴承被损坏,必须更换支架。 轴承不可单独维修。
Show/hide table图 2 g01007192 - 在壳体 (14)上安装O形密封圈。 在支架 (16)上安装壳体 (14)和衬套 (15)。
Show/hide table
图 3 g01007191 - 在壳体 (14)内安装惰轮齿轮 (12)和驱动轴 (13)。
Show/hide table
图 4 g01007155 注: 如果板 (9)里的轴承被损坏,则必须更换该板。 轴承不可单独维修。
- 在与密封垫 (11)相对的板的一侧安装O形密封圈。 安装板 (9)。 安装密封垫 (11)。
Show/hide table
图 5 g01007154 注: 在盖 (8)上安装单向阀 (10)前,确保单向阀上的弹簧朝里。
- 在缸盖 (8)上安装单向阀 (10)。
Show/hide table
图 6 g01007146 - 在板 (9)上安装盖 (8)。
- 安装螺栓 (7).
Show/hide table
图 7 g01007139 Show/hide table弹簧加压的零件和/或盖板可能导致人身伤害。
拆卸盖板时弹簧力将被释放。
松动螺栓时做好准备把持住弹簧加载的盖板。
- 将以下零件安装到支架上。 盖 (6), 垫圈 (5), 气门弹簧 (4) 和 提升阀 (3)。
Show/hide table
图 8 g01007133 - 安装O形密封圈 (1).
- 在驱动轴上安装驱动器接头 (2)。
Show/hide table
图 1 | g01007193 |
结束:
- 安装燃油输油泵。 参考拆解与组装, "燃油输油泵 - 安装"。
Caterpillar Information System:
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0338 - FMI 05 Pre-Lube Relay open circuit
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0274 - FMI 03 Atmospheric Pressure open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0273 - FMI 13 Turbo Outlet Pressure calibration required
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0273 - FMI 04 Turbo Outlet Pressure short to ground
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0273 - FMI 03 Turbo Outlet Pressure open/short to +batt
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0268 - FMI 02 Check Programmable Parameters
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0254 - FMI 12 Electronic Control Module Error
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0253 - FMI 02 Personality Module mismatch
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0168 - FMI 02 System Voltage intermittent/erratic
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0168 - FMI 01 System Voltage Low
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0168 - FMI 00 System Voltage High
3500B and 3500B High Displacement Generator Set Engines MID 036 - CID 0110 - FMI 04 Engine Coolant Temperature short to ground
G3408 and G3412 Engines Valve Mechanism
3114, 3116 and 3126 Engines Engine Has Early Wear
3114, 3116 and 3126 Engines Engine Misfires, Runs Rough or Is Unstable
SR500 Generators General Hazard Information
3034 Engine for Caterpillar Built Machines Fuel Shutoff Solenoid - Remove and Install
G3500 Engines Air Inlet Manifold - Remove and Install
G3500 Engines Drive Housing (Front) - Remove and Install
G3500 Engines Air Cleaner - Remove and Install
SR500 Generators Engine Stopping
3116 and 3126 Marine Engines Gauges and Indicators
Electronic Modular Control Panel II (EMCP II) For MUI Engines Pulse Width Modulated (PWM) Sensor - Test
3116 Truck Engine Aftercooler Core - Clean/Test - Air-To-Air Aftercooler