Engine Oil Filter Base - Assemble
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检查 O 形密封圈的状况。 必要时,更换密封件。
- 安装将机油滤清器固定在机油滤清器底座上的螺柱。 将螺柱拧紧至扭矩为
68 ± 7 N·m (50 ± 5 lb ft) 。Show/hide table图 1 g01176830 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 将安全阀柱塞 (15) 和弹簧 (17) 安装在机油滤清器底座 (11) 内。
- 将 O 形密封圈 (16) 放在螺塞 (18) 上并且将螺塞安装到机油滤清器底座 (11) 中。
Show/hide table
图 2 g01176829 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 将下列项安装到机油滤清器底座 (11) 内:油泵旁通阀 (8) , 弹簧 (9) 和 O 形密封圈 (14)。
- 安装盖 (10)、螺栓和垫圈。
- 将 O 形密封圈 (12) 和气门 (13) 安装在机油滤清器底座 (11) 中。
- 安装用来固定安全阀 (13) 的螺栓和垫圈。
Show/hide table
图 3 g01176828 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 将下列项安装到机油滤清器底座中:挡圈 (6), 弹簧 (4), 安全阀簧座 (7) 和 隔套 (3)。
- 安装螺栓 (5)。
Show/hide table
图 4 g00513002 - 安装安全阀组件 (2) 。
- 将 O 形密封圈 (1) 安装在机油滤清器底座上。
结束:
- 安装发动机机油滤清器底座。 请参阅拆解和组装, "发动机机油滤清器底座 - 安装"。
Caterpillar Information System:
3304B and 3306B Engines for Caterpillar Built Machines Rocker Shaft - Assemble
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Filter Base - Disassemble
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Filter Base - Install
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Filter Base - Remove
3126 Truck Engine (Military) Cold Weather Lubricants
3304B and 3306B Engines for Caterpillar Built Machines Rocker Shaft - Disassemble
Installation and Maintenance Of The 157-1946 Air Temperature Control for Cooling of Control Panels{1928} Installation and Maintenance Of The 157-1946 Air Temperature Control for Cooling of Control Panels{1928}
3306B Industrial Engine Rocker Shaft and Pushrod - Install
3406E On-Highway Engine Compression Brake - Assemble - If Equipped
3176C and 3196 Industrial Engines Engine Centrifugal Oil Filter - Remove and Install
3406E On-Highway Engine Electronic Unit Injector - Remove
3176C and 3196 Engines For Caterpillar Built Machines Exhaust Manifold - Remove and Install
3406E On-Highway Engine Electronic Unit Injector - Install
3608 Engine Fuel Transfer Pump
3116 and 3126 Marine Engines Model View Illustrations
G3300 Engines Gauges and Indicators
3176C and 3196 Engines For Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
3406E On-Highway Engine Turbocharger - Remove
3608 Engine Fuel Injection Control Linkage
3306B Industrial Engine Valve Mechanism Cover - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
3116 and 3126 Marine Engines Engine Rating Definitions
3176C and 3196 Engines For Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3524B Engines for Off-Highway Trucks Engine Cranks but Will Not Start