Electronic Unit Injector - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
B | 9U-6862 | 锥形碳刷 | 1 |
9U-7237 | 刷子扩展工具 | 1 | |
C | 9U-6863 | 小号孔刷 | 1 |
9U-7237 | 刷子扩展工具 | 1 | |
D | 8T-2998 | 润滑剂 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (B) 来清洁电子单体喷油器的喷油器座圈 (8)。
- 使用工具 (C) 清洁顶端孔 (9) 。
Show/hide table
图 2 g01061150 Show/hide table注意 不要重复使用 O 形密封圈。 必须使用新 O 形密封圈。
- 将 O 形密封圈 (10) 安装到电子单体喷油器 (3) 上。
- 用按 50/50 混合的清洁的机油和工具 (D) 稍微润滑孔。
Show/hide table
图 3 g01061151 注: 如果喷油器已经改动,则随后会使用喷油器修整代码 (11)。 记下位于电磁阀上的喷油器修整代码 (11)。
Show/hide table注意 当使用喷油器总成的时候,新喷油器总成的电子喷油器代码必须通过电子维修工具上的校准菜单编入发动机个性模块软件中。 如果没有输入新的燃油喷油器总成的电子编码,则假定为以前燃油喷油器总成特征。
如果不可能立刻将喷油器的电子喷油器代码重新编入到个性模块软件中,发动机不会严重受损。 不过应该尽快重新编入新电子喷油器的代码,以便能尽快达到发动机的最优性能。
Show/hide table图 4 g01055070 - 将电子单体喷油器 (3) 安装到缸盖中的原有位置。
- 安装固定卡箍 (7)。
Show/hide table
注意 不要重复使用喷油器压紧螺栓。 必须使用新的喷油器压紧螺栓。
Show/hide table注意 在拆卸过程中,如果喷油器固定螺栓松动,应及时检查喷油器孔的磨损和破损情况。 换掉垫圈和隔套。
注: 使用新的螺栓 (5)。
- 安装用来将电子单体喷油器固定就位的隔套组件 (6) 和螺栓 (5)。
- 将电子单体喷油器完全拉入孔径内。 按照下列步骤拧紧螺栓。
- 将单体喷油器的螺栓拧紧至扭矩
30 ± 7 N·m (22 ± 5 lb ft) 。 - 松开螺栓,直至可以用手转动螺栓。
- 再次将单体喷油器的螺栓拧紧至扭矩
30 ± 7 N·m (22 ± 5 lb ft) 。
- 将单体喷油器的螺栓拧紧至扭矩
- 将线束组件 (2) 安装在电子单体喷油器 (3) 上。 拧紧盖螺母至扭矩为
2.5 ± 0.25 N·m (22 ± 2 lb in) 。 - 将桥组件 (4)安装在气门杆上。
Show/hide table
图 5 g01019031 - 将螺塞 (1) 安装在燃油歧管内。
Show/hide table
图 1 | g01061148 |
结束:
- 安装摇臂轴组件和推杆。 请参阅拆解和组装, "摇臂轴和推杆 - 安装"。
Caterpillar Information System:
3304B and 3306B Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
3176C and 3196 Engines For Caterpillar Built Machines Electronic Unit Injector - Remove
3306B Industrial Engine Basic Block
G3300 Engines Model View Illustrations
3176C and 3196 Engines For Caterpillar Built Machines Fuel Transfer Pump - Install
3176C and 3196 Engines For Caterpillar Built Machines Fuel Transfer Pump - Remove
3176C and 3196 Engines For Caterpillar Built Machines Fuel Priming Pump - Remove and Install
3306B Industrial Engine Power Take-Off Clutch
3306B Industrial Engine Power Take-Off Clutch
3176C and 3196 Engines For Caterpillar Built Machines Air Compressor - Remove and Install
3406E On-Highway Engine Camshaft Bearings - Install
3306B Industrial Engine Power Take-Off Clutch
3306B Industrial Engine Electrical System
3176C and 3196 Engines For Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
3304B and 3306B Engines for Caterpillar Built Machines Housing (Front) - Remove
3176C and 3196 Engines For Caterpillar Built Machines Electronic Unit Injector Sleeve - Install
3306B Industrial Engine Air Starting System
3304B and 3306B Engines for Caterpillar Built Machines Housing (Front) - Install
3406E On-Highway Engine Compression Brake - Remove - If Equipped
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Pump - Remove
3406E On-Highway Engine Compression Brake - Install - If Equipped
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Pump - Install
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Pump - Disassemble