Pistons and Connecting Rods - Disassemble
Disassembly Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 7S-9470     | Piston Ring Expander     | 1     |
B     | 5P-8639     | Press Group     | 1     |
5P-8645 | Adapter     | 1     | |
6V-3029 | Spacer     | 1     | |
6V-2049 | Adapter     | 1     | |
1U-5230 | Hand Hydraulic Pump     | 1     | |
8F-0024 | Hose     | 1     | |
1P-2375 | Connecting Coupler     | 1     | |
1P-2376 | Connecting Coupler     | 1     |
Start By:
- Remove the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Remove" .
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove the piston rings from the pistons with tool (A) .
Show/hide table
Illustration 1 | g00484932 |
- Remove retaining ring (3) , piston pin (1) and connecting rod (2) .
Show/hide table
Illustration 2 | g00484980 |
- Remove the connecting rod bearing.
- Heat the connecting rod in an oven to a temperature of 176 to 260 °C (350 to 500 °F). Do not use a direct flame to heat a connecting rod.
- Put 6V-3029 Spacer (11) into the base plate. Put the connecting rod on the base plate of Tool (B) .
Show/hide table
Illustration 3 | g00485038 |
Show/hide table
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin. |
- Put the connecting rod piston pin bearing end in the center of the port assembly of Tool (B) . Install pin (5) in the center of the bore for the connecting rod bearing.
- Install 6V-2049 Adapter (9) . Align the hole in the adapter with the hole in the base plate of tool (B) .
- Install clamp bar (10) and clamp pin (4) .
Note: The old piston pin bearing is removed while the new piston pin bearing is installed.
- Put the new piston pin bearing on the connecting rod. Install 5P-8645 Adapter (8) with the tapered end of the adapter toward the piston pin bearing. The piston pin bearing joint must be in alignment with the hole in adapter (9) and the base plate of Tool (B) .
- Install adapter (7) from the press group on adapter (11) .
- Use Tool (B) to push the new piston pin bearing (6) into the connecting rod. Press piston pin bearing (6) into position until adapter (8) makes contact with the connecting rod surface.
- Remove the connecting rod and the old piston pin bearing from Tool (B) .
- Check the piston pin bearing bore diameter after the bearing is installed. The correct inside diameter is 43.210 ± 0.008 mm (1.7012 ± 0.0003 inch). The clearance between the bearing and the piston pin must not be more than 0.08 mm (0.003 inch). Refer to Special Instruction, SMHS7295 for additional information on removing the piston pin bearings.
Caterpillar Information System:
G3500B Engines Engine Oil Pressure Sensor
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 190 FMI 2 Speed Sensor (Engine) Incorrect Signal - Test
G3500B Engines Manifold Air Pressure Sensor
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 168 FMI 4 Electrical System Voltage Below Normal - Test
C-18 Truck Engines S·O·S Coolant Analysis
3126 Truck Engine (Military) S·O·S Oil Analysis
G3612 and G3616 Engines Exhaust Bypass Valve
G3612 and G3616 Engines Air Lines - Choke
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 168 FMI 3 Electrical System Voltage Above Normal - Test
3412E, C30 and C32 Marine Engines Connecting Rod Bearings - Install
3406E On-Highway Engine Crankshaft Front Seal - Install
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 111 FMI 3 Fluid Level Sensor (Engine Coolant) Voltage Above Normal - Test
G3500B Engines Oxygen Sensor
G3500B Engines Detonation Sensor
Electronic Modular Control Panel II (EMCP II) for EUI Engines CID 190 FMI 3 Speed Sensor (Engine) Voltage Above Normal - Test
3306C Truck Engine Lifter Group - Remove and Install
G3612 and G3616 Engines Cooling System
G3612 and G3616 Engines Air Inlet and Exhaust System
P16, P20, P25, P28, P40 and P60 Pulverizers Pulverizer Cylinder
P16, P20, P25, P28, P40 and P60 Pulverizers Pulverizer Mounting
P16, P20, P25, P28, P40 and P60 Pulverizers Crusher Tooth
P16, P20, P25, P28, P40 and P60 Pulverizers General Information
G3612 and G3616 Engines Lubrication System
P16, P20, P25, P28, P40 and P60 Pulverizers Rotator Motor