1. Home
  2. Caterpillar
  3. Operation and Maintenance Manual
  4. #i07711203

Cat ® Command for Dozing, Gen 3.5 Remote Control Operator Console with RFID for D9T Track Type Tractor Caterpillar


Return to Manual Operation

Usage:

D9T NJH

  • Park the machine in a safe area.

  • Lower the implements.
    Show/hide table
    Illustration 1g06405406
    Operator console
    (1) Engine deceleration lever
    (2) Service brake lever
    (3) Status display
    (4) Implement select switch
    (5) High-idle engine speed select dial
    (6) Blade float select button
    (7) Blade assist mode select button
    (8) Blade pitch / ripper control knob
    (9) Implements control
    (10) Implement lockout switch
    (11) Machine power / engine crank switch
    (12) Parking brake switch
    (13) Steering / direction control
    (14) Gear shift up / down knob
    (15) Avoidance zone LED (not used)
    (16) Parking brake LED
    (17) (Not used)
    (18) Fire suppression switch (if equipped)
    (19) Active fault LED
    (20) Implement lockout LED
    (21) Battery / wireless status LED
    Show/hide table
    Illustration 2g06229164
    Left side of operator console
    (22) Engine high / low idle button
    (23) Display select button
    Show/hide table
    Illustration 3g06229168
    Right side of operator console
    (24) Operator console power button
    (25) Horn button
    (26) Operator console commanded stop switch
    (27) Not used this machine series
    (28) Machine work light button
    (29) RFID chip slot

  • Engage the Parking Brake switch (12).

  • Engage the Implement Lockout switch (10).

  • Place the Machine Power/Engine Crank switch (11) in the OFF position.

  • Hold down the Operator Console Power Button (24) for 5 Seconds.

    Note: The blue indicator light on top of the machine will now be solid blue. All power is removed from the operator console.

    Note: Let the engine cool down before restarting in manual mode.

    Machine

    Show/hide table
    Illustration 4g06411392
    Manual override switch and manual/remote mode switch mounted on the instrument panel in the cab
    (40) Manual override switch
    (41) Manual/remote mode switch

    Note: Illustration 4 displays the Manual/Remote Mode switch (41) is in the MANUAL position.

    Access the Manual/Remote Mode switch (41) on the instrument panel in the cab and rotate from REMOTE to MANUAL.

    Note: Leaving the switch in the REMOTE position can drain battery power when the machine is not running. Only the battery disconnect switch will prevent this switch from draining the battery power.

    Operate Alternate Machines

    On-Board Receiver and Radio Frequency Identification (RFID) Chip

    The Command for Dozing system contains an On-Board Receiver and Radio Frequency Identification (RFID) Chip that has been specially paired. This pairing cannot be rewritten or modified to allow use of another device. This pairing allows one Operator Console to operate one Remote Control Machine while not interfering with another existing Command for Dozing Machine.

    Link an Operator Console to the On-Board Receiver

    The Operator Console can only be used to control one machine at a time, however the Operator Console can be used to control an alternate remote control machine by linking the Operator Console to a new On-Board Receiver.

    Linking an On-Board Receiver to an Operator Console is followed as:

    1. Locate the Operator Console, On-Board Receiver, and RFID Chip.

    2. Insert the RFID Chip into the Operator Console.

    3. Power up the Operator Console (In accordance with the OMM).

    To Link the Operator Console to another machine:

    1. Locate the Operator Console, and RFID Chip from the Alternate Command for dozing Machine.

    2. Remove existing RFID Chip.

    3. Insert RFID Chip from the other Command for dozing machine.

    4. Power up the Operator Console (In accordance with the OMM).

    • Caterpillar Information System:

    Cat ® Command for Dozing, Gen 3.5 Remote Control Operator Console with RFID for D9T Track Type Tractor Stopping the Machine
    Cat ® Command for Dozing, Gen 3.5 Remote Control Operator Console with RFID for D9T Track Type Tractor Operation
    Cat® Terrain v7 for Grading and Loading As-Built Surfaces
    Cat® Terrain v7 for Grading and Loading Master Configuration File
    Cat ® Command for Dozing, Gen 3.5 Remote Control Operator Console with RFID for D9T Track Type Tractor Before Operation
    Cat® Terrain v7 for Grading and Loading Information from Receiver - Position Accuracy
    PM310, PM312, and PM313 Cold Planer Additional Messages
    Installation Procedure for Tire Pressure Monitoring Kit for 844K, 854K Wheel Dozers and 990K, 992K, and 994K Wheel Loaders {1408, 7490, 7494} Installation Procedure for Tire Pressure Monitoring Kit for 844K, 854K Wheel Dozers and 990K, 992K, and 994K Wheel Loaders {1408, 7490, 7494}
    Cat® Terrain v7 for Grading and Loading Avoidance Zone
    PM310, PM312, and PM313 Cold Planer Water Spray System
    Cat® Terrain v7 for Grading and Loading Materials Windows
    Cat® Terrain v7 for Grading and Loading VBM, DIG and TSS Files for Material Grade Design
    Cat ® Command for Dozing, Gen 3.5 Remote Control Operator Console with RFID for D9T Track Type Tractor Operator Assist Systems
    Cat® Terrain v7 for Grading and Loading Machine to Machine As-Built Surface Update
    Cat® Terrain v7 for Grading and Loading Listen to Multicast Information
    Cat® Terrain v7 for Grading and Loading All Machines Position Message System
    Cat® Terrain v7 for Grading and Loading Customer Supplied Position System Interface
    Cat® Terrain v7 for Grading and Loading Troubleshooting
    New Coolant Lines for Pump Electronic Tank Unit (PETU) are Now Used on Certain Off-Highway Trucks {108U, 1380} New Coolant Lines for Pump Electronic Tank Unit (PETU) are Now Used on Certain Off-Highway Trucks {108U, 1380}
    Improved Front Cylinder Block Gaskets are Now Used on Certain C27 and C32 Machine Engines {1151, 1162, 7555} Improved Front Cylinder Block Gaskets are Now Used on Certain C27 and C32 Machine Engines {1151, 1162, 7555}
    Cat® Terrain v7 for Grading and Loading Software
    Cat® Terrain v7 for Grading and Loading System Components
    Cat ® Command for Dozing, Gen 3.5 Remote Control Operator Console with RFID for D9T Track Type Tractor Specification
    Cat ® Command for Dozing, Gen 3.5 Remote Control Operator Console with RFID for D9T Track Type Tractor General Maintenance Information
    Back to top
    Contacts My AVS
    The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
    CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.