| |
| Illustration 1 | g06243463 |
| |
| Illustration 2 | g06164645 |
There are several specific messages on this machine. The location of the messages and the description of the messages are reviewed in this section. Become familiarized with all messages.
Make sure that all the messages are legible. Clean the messages or replace the messages if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the messages, use a cloth, water, and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the messages. Loose adhesive will allow the messages to fall.
Replace any message that is damaged, or missing. If a message is attached to a part that is replaced, install a message on the replacement part. Any Prentice dealer can provide new messages.
Diesel Fuel Requirements (1)
This message is located next to the fuel filler cap in the fuel fill access compartment.
| |
| Illustration 3 | g02157153 |
| NOTICE |
|---|
|
Ultra Low Sulfur Diesel (ULSD) fuel will have ≤15 ppm (0.0015%) sulfur using the "ASTM D5453", "ASTM D2622", or "DIN 51400" test methods. Certain applications and/or governments/localities MAY require the use of ULSD fuel. Emission controlled diesel engines and/or diesel engines equipped with exhaust aftertreatment devices MAY require the use of Ultra Low Sulfur Diesel (ULSD) fuel. Consult federal, state, and local authorities for guidance on fuel requirements for your area. Also, consult the specific engine Operation and Maintenance Manual for guidance. Caterpillar does not mandate the across the board use of ULSD fuel in non-road and stationary applications, but does allow its use. When ULSD is used, there are concerns with fuel viscosity, lubricity, and thermal stability. The fuel viscosity, lubricity, and thermal stability limits stated in the Caterpillar Specification for Distillate Diesel Fuel address these concerns. In North America, diesel fuel that is identified as "ASTM D975 Grade No. 1-D S15" or "ASTM D975 Grade No. 2-D S15" and meet the "ASTM D975 Thermal Stability Guideline X2.10.2.2", generally meet the Caterpillar requirements for ULSD fuel. 2007 and newer mdoel lyear on-highway diesel engines are required to use fuel with 15 ppm or less sulfur. |
Product Link (2)
Your machine is equipped with the Product Link System, this additional message is on the cab door.
| |
| Illustration 4 | g01418953 |
The Product Link System is a satellite or cellular communication device that transmits information regarding the machine back to Prentice dealers and customers. All logged events and diagnostic codes that are available to the Cat Electronic Technician (ET) can be sent to satellite or cellular tower. Information can also be sent to the Product Link System. The information is used to improve Cat products and Cat services.
Air Conditioner (3)
This message is on the left-hand front of the heater/evaporator assembly.
| |
| Illustration 5 | g03338001 |
This message for the air conditioner has the appropriate information for the following services: the air conditioner lubricant.
Follow instruction to avoid engine damage.
Reference: See Operation and Maintenance Manual, "Maintenance Interval Schedule" for all maintenance recommendations.
Alternate Exit (4)
This message is on the lower front corner of the right-hand sliding window.
| |
| Illustration 6 | g03337999 |
This message indicates the correct alternate exit path.
Window Cleaning (5)
This message is on the left-hand rear corner of the skylight.
| |
| Illustration 7 | g00930685 |
Reference: For more information, refer to Operation and Maintenance Manual, "Windows - Clean".
Fire Point (Engine) (6)
This message is on the front engine enclosure door, over the Fire Extinguisher Access Hole.
| |
| Illustration 8 | g02095974 |
This message describes the fire point that is available on the engine compartment. Use the aperture to suppress fire hazard in the engine compartment.
Do not use an unsafe method to suppress fire hazard in the engine compartment.
Machine Hydraulic System (7)
The following message is on the hydraulic oil fill pump pipe support bracket.
| |
| Illustration 9 | g02096113 |
This machine hydraulic system is filled with Cat HYDO Advanced oil.
Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for more information about the hydraulic oil.
Fuse Panel Identifier (8)
The following message is on the inside console door fuse/relay panel access.
| |
| Illustration 10 | g06162900 |
The messages on the left-hand side of the film identify the function for each fuse and the amperage of each fuse. The messages on the right-hand side of the film identify the relay functions.
Joystick Control Functions (9)
This message is located in the cab on the lower rear surface of the door window.
| |
| Illustration 11 | g03233117 |
This message identifies what function each joystick movement will initiate. Films are applied according to factory settings.
Hydraulic Oil System (10)
This message is on the right-hand side of the hydraulic tank, level with the hydraulic oil sight gauge.
| |
| Illustration 12 | g06162901 |
This message identifies the hydraulic oil fill level information.
DEO-ULS Oil Information (11)
This message is located under the oil fill access cover on the bracket supporting the remote oil fill hose.
| |
| Illustration 13 | g03337954 |
This message identifies the proper oil required for engine.
Grease Identifier (12)
This message is on the outside of the operator cab on the lower rear corner of the front left-hand side panel. Located near the grease fittings on the operator access platform.
| |
| Illustration 14 | g03337966 |
This message identifies the proper grease to use for remote grease fittings.
Power Wash Prohibited (13)
This message is on the inside of the Diesel Exhaust Fluid fill access panel.
| |
| Illustration 15 | g06243353 |
Washing with high-pressure water is prohibited in this area. Manually clean with a wet cloth or sponge.