Window Wiper and Washer
Show/hide table
| |
| Illustration 1 | g06221191 |
|
Front view of cab | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 1 | 12 | - | Torque to |
| 2 | 6 | - | Tighten inner nut to Tighten outer nut to Ensure to hold inner nut steady while tightening outer nut. |
| 3 | 35 | 3S-2093 Cable Strap | Ensure that the tie straps should secure not constrict hose(s).
As required, use the cable straps. |
| 4 | - | - | Torque to |
Show/hide table
| |
| Illustration 2 | g06221179 |
|
Right view of cab | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 5 | 2 | 8T-5400 Connector | Torque to |
| 6 | - | - | Torque to |
Show/hide table
| |
| Illustration 3 | g06221402 |
|
Rear view of cab | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 7 | - | - | Torque to |
| 8 | - | - | Torque to |
| 9 | - | - | Use the following procedure to install the wiper arm: 1. Tighten nut to 2. Wait for minimum of 0.5 hours to 4 hours maximum. 3. Again, tighten nut to |
Show/hide table
| |
| Illustration 4 | g06221463 |
|
8T-5400 Connector | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 10 | - | - | Torque for sheet metal is Use the following procedure for glass installation: 1. Initially tighten to 2. Wait for a minimum of 0.5 hour and 4 hours maximum. 3. Again, tighten to |
Caterpillar Information System:
992K Wheel Loader Systems Oil Pressure Switch (Differential)
992K Wheel Loader Systems Pressure Switch - Hydraulic Oil
A New Oil Suction Screen Cover is Now Used for Certain C175 Off-Highway Truck Engines {1302, 1302} A New Oil Suction Screen Cover is Now Used for Certain C175 Off-Highway Truck Engines {1302, 1302}
424B2 Backhoe Loader Additional Messages
Damper Fluid Kits Are not Available Outside of the United States {1205} Damper Fluid Kits Are not Available Outside of the United States {1205}
C4.4 Industrial Engine Relief Valve (Fuel) - Remove and Install
785G Off-Highway Truck Power Receptacle - 24 Volt
785G OFF-HIGHWAY TRUCK Engine Supplement Temperature Sensor (Exhaust Outlet) - Remove and Install
785G OFF-HIGHWAY TRUCK Engine Supplement Temperature Sensor (Exhaust Inlet) - Remove and Install
C4.4 Generator Set Engines Relief Valve (Fuel) - Remove and Install
An Improved Spindle in the Front Wheel Group is Now Used on Certain 794 AC Off-Highway Trucks {4006, 4251} An Improved Spindle in the Front Wheel Group is Now Used on Certain 794 AC Off-Highway Trucks {4006, 4251}
785G Off-Highway Truck Starting with Auxiliary Start Receptacle - If Equipped with Electric Start
548 Forest Machine Machine System Final Drive
A New Top Liner Seal is Now Used for Certain 3500 Machine Engines with Cuffed Cylinder Liners {1201, 1217, 7555} A New Top Liner Seal is Now Used for Certain 3500 Machine Engines with Cuffed Cylinder Liners {1201, 1217, 7555}
An Improved Fan Drive Assembly is Now Used on Certain 777G Off-Highway Trucks {1359} An Improved Fan Drive Assembly is Now Used on Certain 777G Off-Highway Trucks {1359}
Procedure to Install an Improved Fan Drive Assembly on Certain 777G Off-Highway Trucks {1359} Procedure to Install an Improved Fan Drive Assembly on Certain 777G Off-Highway Trucks {1359}
An Improved Fan Drive Assembly is Now Used on Certain 773G and 775G Off-Highway Trucks {1359} An Improved Fan Drive Assembly is Now Used on Certain 773G and 775G Off-Highway Trucks {1359}
An Improved Fan Drive Assembly is Now Used on Certain 777F Off-Highway Trucks {1359} An Improved Fan Drive Assembly is Now Used on Certain 777F Off-Highway Trucks {1359}
120M, 12M, 140M and 160M Motor Graders Tandem - Check
548 Forest Machine Machine System Joystick Control
Procedure to Install a Power Circuit When Installing the Control Gp – Transmission on Certain H Series Motor Graders {5258} Procedure to Install a Power Circuit When Installing the Control Gp – Transmission on Certain H Series Motor Graders {5258}
New Transmission Control Group is Now Used on Certain H and K Series Motor Graders {5258} New Transmission Control Group is Now Used on Certain H and K Series Motor Graders {5258}
797B Off-Highway Truck Cab - Remove and Install
785G OFF-HIGHWAY TRUCK Engine Supplement Clean Emissions Module - Remove and Install