Aftercooler - Remove and Install - Aftercooler Housing with 24 bolts
- 从辅助水冷系统将冷却液排入合适的容器,以便保存或处理。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
Show/hide table
图 1 g02173968 - 拆下管组件 (1) 和管组件 (2)。
Show/hide table
图 2 g02173971 - 拆下管组件 (3) 和软管组件 (4)。
Show/hide table
图 3 g02173972 - 拆下软管卡箍 (6) 和软管 (7)。 拆下螺栓 (9)、弯头 (5) 和 O 形密封圈。 拆下螺栓 (10)、弯头 (8) 和 O 形密封圈。 对其余的涡轮增压器重复同样操作。
Show/hide table
图 4 g02173973 - 拆下螺栓 (14)。 由两名技师拆下盖 (13)。 盖 (13) 的重量约为
32 kg (71 lb) 。 从管 (12) 上滑下盖 (13)。 从后冷器芯拆下 O 形密封圈。 拆下螺栓 (11)、管 (12) 和 O 形密封圈。 对其他盖重复该步骤。Show/hide table图 5 g02173975 - 从弯头 (16) 上断开管组件 (18)。 拆下螺栓 ( 17 )并从弯头 (16) 上断开管组件和法兰。 拆下 O 形密封圈。 拆下螺栓 (15)、弯头 ( 16)、适配器和 O 形密封圈。
Show/hide table
图 6 g02174147 - 从三通 (20) 拆下螺栓 (19),并拆下卡箍组件。 拆下螺栓 ( 22)、法兰 ( 21) 和三通 (20)。 拆下适配器和 O 形密封圈。
Show/hide table
图 7 g02174148 - 拆下螺栓 ( 23)、盖 (24)、垫片、适配器和 O 形密封圈。
Show/hide table
图 8 g02174212 - 由两名技师拆下后冷器芯 (25)。 后冷器芯 (25) 的重量约为
45 kg (100 lb) 。 将 O 形密封圈从壳体拆下。 对另一个后冷器芯重复该步骤。Show/hide table图 9 g02174219 - 拆下螺栓 (27)。 由两名技师拆下壳体 (26)。 壳体 (26) 的重量约为
26 kg (57 lb) 。 从进气歧管拆下 O 形密封圈。 对其他壳体重复该步骤。
- 将后冷器芯放在其侧面,安装密封圈。 确保它完全就位。 用可移除的胶带粘贴侧面,确保密封件在组装期间保持就位。
Show/hide table
图 11 g06050591 - 提升后冷器芯和顶盖时,请使用适当的起吊设备。 如图 11 所示,在对齐螺栓孔的同时,将后冷器芯垂直放下。 安装顶部后冷器密封件,确保其完全就位。 将顶盖垂直向下安装,确保无倾斜。
Show/hide table
图 12 g06160963 注: 零扭矩参考意味着将螺栓安装到最小阻力。
- 在进气歧管上的凹槽中安装 O 形密封圈。 将下部壳体安装到进气歧管上。
- 以零扭矩安装螺栓,从中间开始并使用图 12 中所示的模式。 使用图 12 中的模式将螺栓拧紧至扭矩
24 N·m (18 lb ft) 并检查密封件是否正确就位、是否有气泡或凸起。 - 使用图 12 中的模式再次将螺栓拧紧至扭矩
47 N·m (35 lb ft) 并检查是否有气泡或凸起。 - 使用图 12 中的模式再次将螺栓拧紧至扭矩
105 ± 20 N·m (77 ± 15 lb ft) 。Show/hide table图 13 g02174212 - 将 O 形密封圈安装在壳体上。 由两名技师安装后冷器芯 (25)。 后冷器芯 (25) 的重量约为
45 kg (100 lb) 。 对另一个后冷器芯重复该步骤。Show/hide table图 14 g02173973 - 将 O 形密封圈安装在后冷器芯上。 由两名技师安装盖 (13)。 盖 (13) 的重量约为
32 kg (71 lb) 。 - 在 O 形密封圈上涂抹一层薄薄的甘油。 在另一个盖上安装 O 形密封圈、管 (12 )和螺栓 (11)。 由两名技师安装另一个盖。 在盖 (13 )中滑动管 ( 12)。 安装螺栓 (14)。 拧紧角部螺栓以安放 O 形密封圈。 随后拧紧其余螺栓。
Show/hide table
图 15 g02174148 - 在 O 形密封圈上涂抹一层薄薄的甘油。 安装 O 形密封圈、适配器、垫片、盖 (24 )和螺栓 ( 23)。 此时不要拧紧螺栓。
Show/hide table
图 16 g02174147 - 在 O 形密封圈上涂抹一层薄薄的甘油。 安装 O 形密封圈、适配器、三通 (20)、法兰 (21 )和螺栓 ( 22)。 安装卡箍组件和螺栓 (19)。 此时不要拧紧螺栓。
Show/hide table
图 17 g02173975 - 在 O 形密封圈上涂抹一层薄薄的甘油。 安装 O 形密封圈、适配器、弯头 ( 16) 和螺栓 (15)。 将管组件和法兰连接至弯头 (16),然后安装螺栓 (17)。 将管组件 (18) 连接到弯头 (16)。 此时不要拧紧螺栓。
Show/hide table
图 18 g06160966 - 使用图 18 中的模式将螺栓拧紧至扭矩
24 N·m (18 lb ft) 。 - 使用图 18 中的模式再次将螺栓拧紧至扭矩
47 N·m (35 lb ft) 。 - 拧紧水弯头的螺栓。
Show/hide table
图 19 g02173972 - 安装 O 形密封圈、弯头 (8) 和螺栓 (10)。 在 O 形密封圈上涂抹一层薄薄的甘油。 安装 O 形密封圈、弯头 (5) 和螺栓 (9)。 安装软管 (7 )和软管卡箍 (6)。 使软管卡箍朝向彼此成 180 度。 对其余的涡轮增压器重复同样操作。
Show/hide table
图 20 g02173971 - 安装软管组件 (4) 和管组件 (3)。
Show/hide table
图 21 g02173968 - 安装管组件 (2) 和管组件 (1)。
- 为辅助水冷系统重新加注冷却液。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
Show/hide table
图 10 | g06050585 |
Caterpillar Information System:
785G Off-Highway Truck Machines Systems Air and Temperature Control - Remove and Install
New Cat® Command for Hauling Software Is Now Available on Certain Cat® Products {7605, 7620} New Cat® Command for Hauling Software Is Now Available on Certain Cat® Products {7605, 7620}
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Sensor Signal (Analog, Passive) - Test
New Machine and Display Software Is Used for Certain Vibratory Soil Compactors {7620} New Machine and Display Software Is Used for Certain Vibratory Soil Compactors {7620}
New Cylinder Head Groups Are Now Used on Certain C175 Off-Highway Truck Engines {1100} New Cylinder Head Groups Are Now Used on Certain C175 Off-Highway Truck Engines {1100}
A New Special Instruction to Rework Single Main Plate Screed to Dual Main Plate Hinged Screed is Now Available for Certain Asphalt Screed {6640} A New Special Instruction to Rework Single Main Plate Screed to Dual Main Plate Hinged Screed is Now Available for Certain Asphalt Screed {6640}
New Water Proof Protections for the Electrical and Generator Boxes are now available for Certain AP300D Asphalt Pavers {1408, 1417, 1420, 1609} New Water Proof Protections for the Electrical and Generator Boxes are now available for Certain AP300D Asphalt Pavers {1408, 1417, 1420, 1609}
Procedure to Install New Water Proof Protections for Electrical and Generator Boxes on Certain AP300D Asphalt Pavers {1408, 1417, 1420, 1609} Procedure to Install New Water Proof Protections for Electrical and Generator Boxes on Certain AP300D Asphalt Pavers {1408, 1417, 1420, 1609}
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Relay - Test
A Procedure to Perform Inspection and Repair of Generator Rotor DC and AC Connections on Certain Electric Drive Off-Highway Trucks is Available {4450} A Procedure to Perform Inspection and Repair of Generator Rotor DC and AC Connections on Certain Electric Drive Off-Highway Trucks is Available {4450}
New Software Is Now Used for Certain 773E 2 Off-Highway Truck Engines {1920} New Software Is Now Used for Certain 773E 2 Off-Highway Truck Engines {1920}
New VIMSpc Software Is Now Available On Certain Cat® Products {7620} New VIMSpc Software Is Now Available On Certain Cat® Products {7620}
CB7 and CB8 Vibratory Asphalt Compactor Machine Systems System Pressure - Release
A Procedure Is Available to Set Up MOBA Leveling System on Certain AP300F and AP355F Asphalt Pavers {7219, 7220} A Procedure Is Available to Set Up MOBA Leveling System on Certain AP300F and AP355F Asphalt Pavers {7219, 7220}
Procedure to Set Up MOBA Leveling System on Certain AP300F and AP355F Asphalt Pavers {7219, 7220} Procedure to Set Up MOBA Leveling System on Certain AP300F and AP355F Asphalt Pavers {7219, 7220}
Procedure to Install Friction Steer Option on Certain AP555F, AP655F, and AP1055F Asphalt Pavers {4300, 4304, 4309, 4310, 4338, 4343} Procedure to Install Friction Steer Option on Certain AP555F, AP655F, and AP1055F Asphalt Pavers {4300, 4304, 4309, 4310, 4338, 4343}
A procedure to install the optional stiffener group on certain SE60v Asphalt Screeds is now available {6643} A procedure to install the optional stiffener group on certain SE60v Asphalt Screeds is now available {6643}
CB7 and CB8 Vibratory Asphalt Compactor Machine Systems Gear Pump Flow - Test
785G Off-Highway Truck Machines Systems Valve (Heater Control) - Remove and Install
CB7 and CB8 Asphalt Compactor Propel System Relief Valve (Charge) - Test and Adjust
CB7 and CB8 Vibratory Asphalt Compactor Machine Systems Relief Valve (Main) - Test and Adjust - Split Drum, Vibratory
CB7 and CB8 Vibratory Asphalt Compactor Machine Systems Relief Valve (Main) - Test and Adjust - Solid Drum, Vibratory
CB7 and CB8 Vibratory Asphalt Compactor Machine Systems Relief Valve (Intercircuit) - Test and Adjust
777F Off-Highway Truck Power Train Tire and Rim (Rear) - Install