Control Valve (Leveling Blade) - Assemble
- 检查并清洗所有零件。 如果任何零件磨损或损坏,则应使用 Caterpillar 新件进行更换。
- 检查所有密封件。 必须更换损坏的密封件。 用新的 Caterpillar 密封件进行更换。
Show/hide table
图 1 g00860947 - 将 O 形密封圈 (34) 和密封 (33) 安装到阀壳体 (1) 中。
Show/hide table
图 2 g00860946 - 将盖 (32) 和螺钉 (31) 安装到阀壳体 (1) 上。 拧紧螺钉 (31) 至扭矩为
16 ± 1 N·m (142 ± 9 lb in) 。Show/hide table图 3 g00860945 - 将 O 形密封圈 (30) 和 O 形密封圈 (29) 安装到滑阀隔套 (28) 中。
Show/hide table
图 4 g00860944 - 将滑阀隔套 (28) 安装到滑阀组件 (24) 上。
- 将滑阀组件 (24) 安装到阀壳体 (1) 中。
Show/hide table
图 5 g00860943 - 将连杆 (26) 和滚销 (27) 安装到滑阀组件 (24) 中。
Show/hide table
图 6 g00860942 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 将弹簧 (25) 安装在滑阀组件 (24) 中。
Show/hide table
图 7 g00860941 - 将钢球 (23) 安装到滑阀组件 (24) 中。
Show/hide table
图 8 g00860940 - 安装隔套 (22) 和滑阀盖 (18)。 将螺钉 (21) 安装到阀壳体 (1) 上。 拧紧螺钉 (21) 至扭矩为
16 ± 1 N·m (142 ± 9 lb in) 。Show/hide table图 9 g00860939 - 将止动套筒 (19) 和钢球 (20) 安装到滑阀盖 (18) 中。
Show/hide table
图 10 g00860938 - 将端盖 (17) 和挡圈 (16) 安装到滑阀盖 (18) 中。
Show/hide table
图 11 g00860937 - 将 O 形密封圈 (15) 安装到安全阀 (14) 上。
Show/hide table
图 12 g00860936 - 将安全阀 (14) 安装到阀壳体 (1) 中。 将安全阀 (14) 拧紧至扭矩为
45 ± 4 N·m (33 ± 3 lb ft) 。Show/hide table图 13 g00860935 - 将 O 形密封圈 (13) 安装到安全阀 (12) 上。
Show/hide table
图 14 g00860934 - 将安全阀 (12) 安装到滑阀部分 (10) 中。 将安全阀 (12) 拧紧至扭矩为
45 ± 4 N·m (33 ± 3 lb ft) 。 - 将 O 形密封圈 (11) 安装到滑阀部分 (10) 中。
Show/hide table
图 15 g00860933 - 安装连杆和螺母 (8)。 将连杆和螺母 (9) 安装到滑阀部分 (10) 上。
- 将阀壳体 (1) 安装到连杆和螺栓 (8) 上。 将阀壳体安装到连杆和螺栓 (9) 上。
Show/hide table
图 16 g00860932 Show/hide table弹簧压缩零件如果安装不当,会伤害人体。
为避免伤害,遵照出版的装配程序,并穿上保护装备。
- 将 O 形密封圈 (7)、提升阀 (6) 和弹簧 (5) 安装到阀壳体 (1) 上。
Show/hide table
图 17 g00860931 - 将滑阀部分 (4) 安装到阀壳体 (1) 上。
- 安装螺母 (2) 和 (3)。 拧紧螺母 (2) 至扭矩为
48 N·m (33 lb ft) 。 拧紧螺母 (3) 至扭矩为19 N·m (168 lb in) 。
结束:
- 安装控制阀(找平铲刀)。
Caterpillar Information System:
MSS3s Machine Security System Glossary of Terms
CP44B and CS44B Vibratory Soil Compactors Machine Systems Control Valve (Leveling Blade) - Disassemble
PL83 and PL87 Pipelayer Systems Piston Pump (Fan Drive)
Repairing Small Cracks In Base Edge Assemblies{0679, 6001, 6120, 6801} Repairing Small Cracks In Base Edge Assemblies{0679, 6001, 6120, 6801}
PL72, PL83 and PL87 Pipelayers Solenoid Return - Test
PL72 Pipelayers Power Train Final Drive - Remove and Install - Right and Left Side
CW34 Pneumatic Compactor Machine Electronic Control System Connector Contact Description
CW34 Pneumatic Compactor Machine Electronic Control System ECM Software - Install
CW34 Pneumatic Compactor Machine Electronic Control System Switch Circuits - Test
CW34 Pneumatic Compactor Machine Electronic Control System Speed Sensor (Dual Signal) - Test
CW34 Pneumatic Compactor Machine Electronic Control System Sensor Signal (Analog, Passive) - Test
PL72 Pipelayers Machine Systems Rollover Protective Structure (ROPS) - Remove and Install
AP500F Asphalt Paver Propel System Piston Pump Neutral - Test and Adjust - Right Propel
MSS3s Machine Security System ECM - Configure
PL72 Pipelayers Power Train Torque Converter Outlet Relief Valve - Remove and Install
MD6200 Rotary Drill Drill Bit - Remove and Install
MSS3s Machine Security System Software - Uninstall - "Immobilizer" Feature
CP44B and CS44B Vibratory Soil Compactors Machine Systems Hydraulic Cylinder (Leveling Blade) - Remove and Install
MSS3s Machine Security System Wiring Harness (Open Circuit) - Test
MSS3s Machine Security System Wiring Harness (Short Circuit) - Test
M314F, M316F, M318F, M320F, M322F, MH3022, MH3024 and MH3026 Wheeled Excavator Engine Supplement Fan - Remove and Install
MSS3s Machine Security System Connector Locations
MSS3s Machine Security System Machine Preparation for Troubleshooting
MSS3s Machine Security System Connector Contact Description