773G and 775G Off-Highway Trucks Caterpillar


Maintenance Interval Schedule

Usage:

773G LRC MWH
在執行任何操作或維護程序之前,請務必先閱讀並理解所有安全資訊、警告及說明。

使用者應對維護的成果負責。 這包括所有調整;使用適當的潤滑劑、油液、濾清器,以及因正常磨損和老化而更換組件。 若未能遵循適當的維護週期和程序,可能會導致產品性能降低和/或組件加速磨損。

若要確定維護週期,請使用里程數、油耗、工時或日程為標準,以先發生的為準。 在惡劣操作條件下運作的產品可能需要更頻繁的維護。 請參閱維護程序,以瞭解是否有任何其他可能會造成維護週期發生變化的例外情況。

附註根據法規定義,排氣後處理系統可在引擎的可用壽命期間 (氣體排放耐用期) 內正常運作。 必須遵守所有規定的維護要求。

附註必須先執行完先前週期的所有保養,才能執行後續週期的各項保養。

使用機器或機器系統的工時表,以判斷應執行保養的時機。

需要時的保養

空調濾清器 - 清潔
自動潤滑儲存槽 - 加注
蓄電池 - 回收
蓄電池或蓄電池電纜 - 檢查/更換
駕駛室空氣濾清器 - 清潔/更換
冷卻系統冷卻液 (ELC) - 更換
顯示器和攝影機 - 清潔
引擎空氣濾清器粗濾芯 - 清潔/更換
引擎空氣濾清器細濾芯 - 更換
引擎空氣粗濾清器 - 清潔
乙醚輔助起動油缸 - 更換
燃油系統 - 加注
燃油系統 - 灌注
保險絲、斷路器及繼電器 - 更換/重設
高強度放電燈 (HID, High Intensity Discharge) - 更換
機油濾清器 - 檢查
輪圈 - 檢查
濾網 (起重裝置和煞車油箱) - 檢查/清潔/更換
吸入濾網 (變矩器回油) - 清潔
牽引力控制系統 (TCS,Traction Control System) - 測試
窗戶清洗器儲液瓶 - 加注
窗戶雨刷 - 檢查/更換
窗戶 - 清潔

每10工作小時或每日的保養

備份警報 - 測試
煞車、指示器和儀表 - 測試
煞車系統 - 測試
冷卻系統冷卻液液位 - 檢查
差速器和最終驅動系統油位 - 檢查
引擎機油油位 - 檢查
燃油系統主要濾清器 (油水分離器) - 排放
燃油箱水和沉澱物 - 排放
起重裝置和煞車油箱油位 - 檢查
安全帶 - 檢查
輔助轉向 - 測試
轉向系統油位 - 檢查
變矩器和變速箱油位 - 檢查

每 50 工作小時或每週的保養

車體樞軸軸承 - 潤滑
中央潤滑系統 - 潤滑
前懸吊汽缸 - 潤滑
起重裝置汽缸軸承 - 潤滑
磁性塞 (車輪) - 檢查
後輪軸 A 形架軸承 - 潤滑
後輪軸外殼橫向控制桿軸承 - 潤滑
後懸吊汽缸軸承 - 潤滑
轉向油缸軸承 - 潤滑
轉向橫拉桿和銷軸承 - 潤滑
輪胎充氣 - 檢查

每250工作小時或每1個月的保養

驅動軸滑動接頭 - 潤滑
風扇驅動軸承和皮帶張緊器滑輪 - 潤滑

最初 500 工時的保養

引擎煞車從動活塞間隙 - 檢查/調整
引擎閥間隙 - 檢查/調整
引擎閥旋轉器 - 檢查
機架和車體支撐墊 - 清潔/檢查

最初 500 工作小時 (適用於新系統、再注滿系統,和轉換系統)

冷卻系統冷卻液樣本 (2 級) - 取樣

每500工作小時的保養

冷卻系統冷卻液樣本 (1 級) - 取樣
差速器和最終驅動系統油樣 - 取樣
引擎機油樣本 - 取樣
前輪機油樣本 - 取樣
起重裝置和煞車油箱機油樣本 - 取樣
轉向系統機油樣本 - 取樣
變矩器和變速箱機油樣本 - 取樣

每500工作小時或每3個月的保養

皮帶 - 檢查/更換
差速器和最終驅動系統機油 - 檢查
引擎曲軸箱通氣管 - 清潔
引擎機油和濾清器 - 更換
機架 - 清潔/檢查
前輪機油 - 更換
前輪機油 - 檢查
前輪油位 - 檢查
燃油系統主要濾清器 (油水分離器) - 更換
燃油系統次要濾清器 - 更換
燃油箱蓋和過濾器 - 清潔
吸入濾網 (變速箱回油) - 清潔
懸吊汽缸 - 檢查

每1000工作小時或每6個月的保養

通氣管 (起重裝置和煞車油箱) - 更換
通氣管 (轉向油箱) - 更換
通氣管 (變矩器和變速箱) - 更換
機架和車體 - 檢查
機架和車體支撐墊 - 清潔/檢查
起重裝置和煞車油箱機油 - 更換
機油濾清器 (煞車) - 更換
機油濾清器 (動力傳動系統) - 更換
機油濾清器 (轉向) - 更換
滾翻保護結構 (ROPS, Rollover Protective Structure) - 檢查
座椅懸吊裝置 - 檢查/潤滑
行駛煞車 - 檢查
轉向連桿 - 檢查
轉向系統機油 - 更換
變矩器和變速箱機油 - 更換

每2000工作小時或每1年的保養

通氣管 (差速器和最終驅動系統) - 更換
差速器止推銷間隙 - 檢查

每年

冷卻系統冷卻液樣本 (2 級) - 取樣

每 2 年

接收器乾燥器 (冷媒) - 更換

每3000工作小時或每2年的保養

冷卻系統壓力蓋 - 清潔/更換
電子單體噴射器 - 檢查/調整
引擎煞車從動活塞間隙 - 檢查/調整
引擎閥間隙 - 檢查/調整
引擎閥旋轉器 - 檢查
機油濾清器 (轉向泵箱體排放) - 更換
散熱器芯子和後冷器 - 清潔

每3年

安全帶 - 更換

每 4000 工時或 1 年

差速器和最終驅動系統機油 - 更換

每隔6000工作小時或3年的保養

冷卻系統冷卻液延長劑 (ELC, Extended Life Coolant, 長效冷卻液) - 添加

每 6000 工時或 4 年

冷卻系統水溫調節器 - 更換

每 7,500 工時或 568,500 公升 (150,000 美制加侖)燃油

引擎組件 - 重建/安裝 Reman
引擎水泵 - 檢查

每 10,000 工作小時的保養

轉向球頭螺栓 - 更換

每12000工作小時或每6年的保養

冷卻系統冷卻液 (ELC) - 更換

每 15,000 工時

輪圈 - 檢查

每 15,000 工時或 1,137,000 公升 (300,000 美制加侖)燃油

引擎組件 - 清潔/檢查、重建/安裝 Reman、安裝新組件

Caterpillar Information System:

PL72 Pipelayer Power Train System Oil And Screens - Change/Clean
735C and 745C Articulated Trucks Machine Systems Secondary Steering System
MH3037 Material Handler Machine Systems Blower Motor (Air Conditioner and Heater) - Remove and Install
RM500B Reclaimer Mixer Power Train Relief Valve (Charge Pressure, Left Propel Pump) - Test and Adjust
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Calibration Using Electronic Service Tool
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 General Information (Calibration)
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Simple Calibration
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Calibration Using Display Module
416F2, 420F2 and 430F2 Backhoe Loaders Lubricant Viscosities - Fluids Recommendations
Instructions For Installing A Heat Shield For The Battery And Circuit Box On Certain 16M Motor Graders{7513} Instructions For Installing A Heat Shield For The Battery And Circuit Box On Certain 16M Motor Graders{7513}
416F2, 420F2 and 430F2 Backhoe Loaders Differential Oil Sample (Rear) - Obtain
416F2, 420F2 and 430F2 Backhoe Loaders Differential Oil Sample (Front) - Obtain
773G and 775G OEM Off-Highway Truck Chassis Maintenance Interval Schedule
MH3037 Material Handler Machine Systems Heating and Air Conditioning Unit - Remove and Install
RM500B Reclaimer Mixer Power Train Case Drain Pressure for Piston Motor (Propel) - Test
Reuse and Salvage Guideline for Unit Rig Mining Truck Hydraulic Steering Cylinders{0374, 0599, 0732, 4303} Reuse and Salvage Guideline for Unit Rig Mining Truck Hydraulic Steering Cylinders{0374, 0599, 0732, 4303}
PM310, PM312, and PM313 Cold Planer Track Information
MH3037 Material Handler Machine Systems Refrigerant Condenser - Remove and Install
MH3037 Material Handler Machine Systems Storage Box and Covers (Cab) - Remove and Install
MH3037 Material Handler Engine Supplement Hood - Remove and Install
MH3037 Material Handler Machine Systems Seat Suspension - Remove and Install
735C and 745C Articulated Trucks Machine Systems Metering Pump (HMU)
2015/01/09 New Power Train Software Gp (Transmission, Chassis) Is Now Used On Certain Large Off-Highway Trucks {7620}
2014/11/25 A New Machine Software Gp(Brake) is Now Available For Certain 785C, 789C, 789D, 793C and 793D Large Off-Highway Trucks {7327, 7620}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.