Heater Core - Remove and Install
Start By:
- Remove the heating and air conditioning unit.
Note: Cleanliness is an important factor. Clean the exterior of the component before disassembly. This will help to prevent dirt from entering the internal mechanism.
- Disconnect harness assemblies (1) and (2).
Show/hide table
Illustration 2 g01187598 - Remove bolts (3).
Show/hide table
Illustration 3 g01187599 - Separate case (4) from case (5).
Show/hide table
Illustration 4 g01187600 - Remove clips (6), (7), and (8).
Show/hide table
Illustration 5 g01187601 - Disconnect coolant temperature sensor (9).
Show/hide table
Illustration 6 g01187603 - Remove bolts (10) and place cover assembly (11) aside.
Show/hide table
Illustration 7 g01187604 - Remove bolt (14) and disconnect lever assembly (12).
- Remove bolt (15) and disconnect lever assembly (13).
Show/hide table
Illustration 8 g01187605 - Place lever assemblies (12) and (13) aside.
- Remove heater core (16).
Show/hide table
Illustration 1 | g01187597 |
- Install heater core (16) in the reverse order of removal.
End By:
- Install heating and air conditioning unit.
Caterpillar Information System:
416F2, 420F2 and 430F2 Backhoe Loaders Differential Oil (Front) - Change
416F2, 420F2 and 430F2 Backhoe Loaders Axle Breathers - Clean/Replace
2014/12/03 An Improved Blade Extension Is Now Available for Certain 120K, 120K Series 2, 12K, 140K, and 160K Motor Graders {6173}
2014/12/16 The Exhaust Bellows Assembly has Been Updated in the New Retrofit Procedure for Certain 797 Off-Highway Trucks {1061, 1067}
2014/11/11 An Improved Assembly and Tightening Sequence is Now Available For Slide Frame and Wear Bar Mounting Bolt for 424B Backhoe Loaders {6508}
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System Electronic Control (Work Tool System)
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System Location of Components (Work Tool System)
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System General Information (Work Tool System)
MH3037 Material Handler Machine Systems Evaporator Coil - Remove and Install
MH3022, MH3024 and MH3026 Material Handlers Hydraulic System Gear Motor (Hydraulic Fan)
A New Latch Assembly Is Now Used on Certain G Series Off-Highway Trucks and Quarry Trucks {7308} A New Latch Assembly Is Now Used on Certain G Series Off-Highway Trucks and Quarry Trucks {7308}
MH3037 Material Handler Machine Systems Swivel - Remove and Install
416F2, 420F2 and 430F2 Backhoe Loaders Differential Oil (Rear) - Change
MH3037 Material Handler Machine Systems Receiver Dryer (Refrigerant) - Remove and Install
416F2, 420F2 and 430F2 Backhoe Loaders Differential Oil Level (Front) - Check
416F2, 420F2 and 430F2 Backhoe Loaders Differential Oil Level (Rear) - Check
416F2, 420F2 and 430F2 Backhoe Loaders Differential Oil Sample (Front) - Obtain
416F2, 420F2 and 430F2 Backhoe Loaders Differential Oil Sample (Rear) - Obtain
Instructions For Installing A Heat Shield For The Battery And Circuit Box On Certain 16M Motor Graders{7513} Instructions For Installing A Heat Shield For The Battery And Circuit Box On Certain 16M Motor Graders{7513}
416F2, 420F2 and 430F2 Backhoe Loaders Lubricant Viscosities - Fluids Recommendations
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Calibration Using Display Module
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Simple Calibration
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 General Information (Calibration)
Medium L and M Series Wheel Loaders Cat Production Measurement Application on Machines Equipped with Product Link: PLE631 or PLE641 Calibration Using Electronic Service Tool