Oscillating and Steering Bar
Show/hide table
 | |
| Illustration 1 | g03743000 |
Show/hide table
| Specification for 379-1680 Oscillating and Steering Bar Gp | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| 1 | 2 | 6D-9281 Clamp As | Use the following procedure in order to tighten locknuts of the clamp assembly: 1. Tighten the locknuts to 109 to 122 N·m (80 to 90 lb ft) during assembly on the machine. 2. Orient the clamp in order to direct the bolt and the locknut in the top side of the steering link (2), as shown in Illustration 1. |
Show/hide table
 | |
| Illustration 2 | g03743009 |
View of area A | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 4 | 8 | 8T-6430 Bolt | Apply blue Loctite 243 to the threads. 1. Use the following procedure in order to tighten the bolt: 2. Tighten the bolts to 60 to 70 N·m (44 to 52 lb ft) to set initial preload on bearings. 3. Rotate leg assembly (3) ten times to ensure proper seating of bearings. 4. Tighten the bolts to 85 to 130 N·m (63 to 96 lb ft) to set final preload. |
| 5 | 2 | 284-8864 Tapered Pin | Before assembly, apply Loctite C5A Copper Anti-Seize to the threads. |
| 6 | 4 | 1B-4444 Nut | Use the following procedure in order to tighten the nuts: 1. Tighten the nuts to 313 to 435 N·m (230 to 320 lb ft) during assembly on the machine. 2. Continue to tighten the nuts to 313 to 435 N·m (230 to 320 lb ft). 3. Do not back off the nuts in order to align the slot for the nuts with the hole of the cotter during assembly of the cotter pin. |
| 7 | 2 | 9F-2247 Pipe Plug | Use the adapter fitting in order to fill cavities with 1P-0808 Multipurpose Grease. Then replace the grease fitting with the pipe plug. |
Caterpillar Information System:
RM500B Reclaimer Mixer Machine Systems Hydraulic Cylinder (Mixing Chamber Rear Door)
RM500B Reclaimer Mixer Machine Systems Rotor Transmission (Rotor Transmission Case and Transmission Planetary)
RM500B Reclaimer Mixer Machine Systems Lines (Steering) - Front
RM500B Reclaimer Mixer Machine Systems Lines (Steering) - Rear
RM500B Reclaimer Mixer Machine Systems Hydraulic Cylinder (Rotor Lift)
AP555F Asphalt Paver Machine Systems Check Valve
RM500B Reclaimer Mixer Machine Systems Piston Motor (Hydraulic Fan)
Command for Underground Diagnostic Codes (Automation ICM)
735C and 745C Articulated Trucks Machine Systems Brake Control Valve (Service)
Cat® Command For Hauling MID 039 - CID 3456 - FMI 03
Cat® Command For Hauling MID 039 - CID 3454 - FMI 05
MH3022, MH3024 and MH3026 Material Handlers Relay - Test
RM500B Reclaimer Mixer Machine Systems Hydraulic Cylinder (Rotor Lift)
CP34 and CS34 Vibratory Soil Compactors Engine Supplement Battery and Battery Cable - Separate and Connect
RM500B Reclaimer Mixer Machine Systems Lines (Cab Slide Cylinder)
RM500B Reclaimer Mixer Machine Systems Lines (Mixing Chamber Front Door Cylinder) - Front
2014/11/03 The Disassembly and Assembly Manual has been Updated for Certain 793C Off-Highway Trucks {0374, 7266, 7301}
RM500B Reclaimer Mixer Machine Systems Lines (Mixing Chamber Front Door Cylinder) - Rear
2015/01/12 An Improved Accessory Drive and Compressor Air Lines Group Is Now Used On Certain 797B Off-Highway Trucks {1207}
C4.4 Engines Welding Precaution
416F2, 420F2 and 430F2 Backhoe Loaders Monitoring System
735C and 745C Articulated Trucks Hoist Control
C4.4 and C7.1 Engines Electronic Service Tools
Procedure to Update the Low Pressure Fuel System on Certain 795F AC Off-Highway Trucks {1251, 1255, 1256, 1261, 1273, 1274, 1290, 1408, 1439} Procedure to Update the Low Pressure Fuel System on Certain 795F AC Off-Highway Trucks {1251, 1255, 1256, 1261, 1273, 1274, 1290, 1408, 1439}