Connection Test
Show/hide table
 | |
| Illustration 1 | g03728549 |
Startup delay screen | |
Tope startup display will delay the running of Tope software to give the machine xIM module time to start up. This screen can be enabled or disabled in the "Tope Config" file.
Show/hide table
 | |
| Illustration 2 | g03728541 |
Connection test screen (1) Connection test pass/fail indicator bubbles (2) IP address of "MineStar" (3) IP address of "CMPD" (4) "Subnet Mask" IP address (5) "Default Gateway" IP address (6) "Start Connection Test" button | |
Perform the following procedure to perform a connection test:
- Log into the system. Refer to Operation and Maintenance Manual, SEBU8837, "Logging In and Logging Out" for more information.
- Ensure that all IP addresses match to the on-site IP addresses.
- In the "CMPD & MineStar Initial Configuration" screen, press the "Start Connection Test" button (6) .
Note: The connection test pass/fail indicator bubbles (1) start initially as a blue circle containing a question mark. The bubbles will change green or red depending on if the test passes or fails.
Caterpillar Information System:
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Fuel System Primary Filter (Water Separator) - Replace
785G Off-Highway Truck Systems Relief Valve (Main)
C4.4 Engines Solenoid Valve - Test - Solenoid Valves that Connect to the Engine ECM
C4.4 Engines Solenoid Valve - Test - Solenoid Valves that Connect to the Dosing Control Unit (DCU)
C4.4 Engines Sensor Signal (Analog, Passive) - Test
C4.4 Engines Sensor Signal (Analog, Active) - Test
C4.4 Engines Sensor Supply - Test
C4.4 Engines Sensor Calibration Required - Test
C4.4 Engines Sensor (Data Link Type) - Test
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Coupler Cylinder
C4.4 Engines Power Take-Off - Test
2015/05/22 Correction to Operation and Maintenance Manual , "Alternate Exit" for Certain Underground Articulated Trucks and Load Haul Dump Machines {7310}
Procedure to Install the Working at Heights Attachment on the 785C and 785D Off-Highway Trucks{0635, 7254, 7255, 7256} Procedure to Install the Working at Heights Attachment on the 785C and 785D Off-Highway Trucks{0635, 7254, 7255, 7256}
2014/11/03 A New Fastener Group Is Now Used on Certain 797F Off Highway Truck Engines {1205, 7553}
2014/12/12 A New Oil Filler Elbow Is Now Used on C175 Off-Highway Truck Engines {1316, 7513}
C7 and C9 Industrial Engines Oil Contains Coolant
785G Off-Highway Truck Systems Hydraulic Tank (Brake, Brake Cooling, Hoist)
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Position Sensor (Lift Linkage) - Replace
950M and 962M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Position Sensor (Tilt Linkage) - Replace
785G Off-Highway Truck Systems Pump Drive Shaft
M318F, M320F and M322F Wheeled Excavators and MH3022 and MH3024 Material Handlers Fire Extinguisher Location
2014/09/30 A New Oil Level Gauge Group is Now Used on Certain 770G and 772G Off-Highway Trucks {1326}
MH3037 Material Handler Machine Systems Cab Riser Cylinder - Remove and Install - Forward/Back Cylinders
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Machine Systems Brake Accumulator - Remove and Install