Piston Pump (Propel) - Remove and Install
拆卸步骤
开始:
- 拆下发动机护罩。 请参阅拆解和组装, "发动机护罩(发动机罩)- 拆卸和安装"。
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 拆卸任何部件或管路之前,必须先把附件降到地面上,让机油先冷却。只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖. |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。
- 将液压油排入适当的容器以便保存或处理。 有关正确的步骤,请参阅操作和保养手册。
- 拆下螺栓,然后将阀组件 (1) 移到一边。
Show/hide table
图 1 | g03335438 |
- 卸下螺栓和板组件 (2) 。
Show/hide table
图 2 | g03335439 |
- 将螺母和电缆组件 (3) 从蓄电池断路开关上拆下。
- 拆下螺栓、板和卡箍 (4) 。
- 将电缆组件 (3) 移到一边。
- 拧松螺母,将正极电缆组件 (5) 从蓄电池上断开。
Show/hide table
图 3 | g03335440 |
- 拆下螺栓和卡箍 (6) 。
- 拆下螺栓、板和卡箍 (7) 。
- 拆下螺栓、板和卡箍 (8) 。
Show/hide table
图 4 | g03335443 |
- 拆下螺栓和卡箍 (9) 。
- 拆下螺栓、板和卡箍 (10) 。 将电缆组件 (3) 移到一边。
Show/hide table
图 5 | g03335444 |
- 拆下螺栓和卡箍 (11) 。 将电缆组件 (5) 移到一边。
- 将适当的起吊设备连接到蓄电池支架 (12) 上。 蓄电池支架 (12) 和蓄电池的重量约为 59 kg (130 lb)。
Show/hide table
图 6 | g03335445 |
- 拆下螺栓 (14) 、蓄电池 (13) 和蓄电池支架 (12) 。
- 拆下螺栓和阀组件 (15) 。
Show/hide table
图 7 | g03335446 |
- 将线束组件 (16) 从活塞泵 (17) 上断开。
- 将软管组件 (18) 从活塞泵 (17) 上断开。
- 将螺栓、法兰和软管组件 (19) 从活塞泵 (17) 上拆下。
- 将适当的起吊设备连接到活塞泵 (17) 上。 活塞泵 (17) 的重量约为 91 kg (200 lb)。
Show/hide table
图 8 | g03335447 |
- 拆下螺栓 (20) 和活塞泵 (17) 。
- 拆下螺栓 (22) 和法兰 (21) 。
Show/hide table
图 9 | g03335448 |
- 拧松螺栓,拆下轮毂组件 (23) 。
Show/hide table
图 10 | g03335452 |
- 将螺栓和适配器板 (24) 从活塞泵 (17) 上拆下。
安装步骤
- 按与拆卸步骤相反的顺序安装活塞泵 (17) 。
- 轮毂组件 (23) 和活塞泵 (17) 的端面之间应为零间隙。
- 拧紧螺栓 (22) 至扭矩为 45 ± 5 N·m (33 ± 4 lb ft)。
Caterpillar Information System:
789D and 789D XQ Off-Highway Truck Air System and Brakes Service Brake Discs - Check - Standard
2013/01/10 TA2 (Technical Analysis) Inspections are Now Available on SIS {0372, 1000, 7000, 753T, 7565}
AP300D Asphalt Paver Machine Systems Operator Platform - Remove and Install
Some Rear Spindles are Machined Incorrectly on Certain 773F and 775F Off-Highway Trucks{4008, 4201, 4205} Some Rear Spindles are Machined Incorrectly on Certain 773F and 775F Off-Highway Trucks{4008, 4201, 4205}
AP300D Asphalt Paver Machine Systems Metering Pump (Steering) - Remove and Install
AP300D Asphalt Paver Machine Systems Hydraulic Tank - Remove and Install
AP300D Asphalt Paver Machine Systems Hydraulic Cylinder (Tow Point) - Remove and Install
AP300D Asphalt Paver Machine Systems Hydraulic Cylinder (Steering) - Remove and Install
AP300D Asphalt Paver Machine Systems Hydraulic Cylinder (Screed Hoist) - Remove and Install
AP300D Asphalt Paver Machine Systems Hydraulic Cylinder (Auger Hoist) - Remove and Install
AP300D Asphalt Paver Machine Systems Hopper - Remove and Install
AP300D Asphalt Paver Machine Systems Generator - Remove and Install
AP300D Asphalt Paver Machine Systems Plates (Drag Pans) - Remove and Install
AP300D Asphalt Paver Machine Systems Push Roller - Remove and Install
AP300D Asphalt Paver Machine Systems Push Roller - Disassemble
AP300D Asphalt Paver Machine Systems Push Roller - Assemble
AP300D Asphalt Paver Machine Systems Screed - Remove and Install
AP300D Asphalt Paver Machine Systems Seat - Remove and Install
AP300D Asphalt Paver Machine Systems Steering Wheel - Remove and Install
AP300D Asphalt Paver Machine Systems Transverse Beam - Remove and Install - If Equipped
AP300D Asphalt Paver Machine Systems Wheel (Front Wheel Assist) - Remove and Install
AP300D Asphalt Paver Machine Systems Wheel (Rear) - Remove and Install
Road Analysis Control Is Logging Excessive Diagnostic Events on 777G Off-Highway Truck{7601, 7632} Road Analysis Control Is Logging Excessive Diagnostic Events on 777G Off-Highway Truck{7601, 7632}
2014/06/20 New Monitor Software Is Now Available for VIMS ABL2M ECM on Certain Cat® Off-Highway Trucks {7601, 7620}