Neutral Start Switch - Adjust
Show/hide table
 |
Diesel engine exhaust contains products of combustion which may cause personal injury. Always start and operate the engine in a well ventilated area, and, if in an enclosed area, vent the exhaust to the outside. |
 |
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part No | Description | Qty |
| A | 146-4080 | Digital Multimeter Gp (RS232) | 1 |
| B | 7X-1710 | Multimeter Probe | 1 |
Note: Perform this procedure if the machine will not start while the propel lever is in NEUTRAL position. Perform this procedure if the machine will start while the lever is out of the NEUTRAL position.
- Drive the machine to a smooth, horizontal surface.
- Move propel lever (1) to the NEUTRAL position.
Show/hide table
 | |
| Illustration 1 | g03148936 |
- Move parking brake switch (2) to the ON position.
- Use throttle control switch (3) in order to operate the engine in low idle.
Show/hide table
 | |
| Illustration 2 | g03148937 |
- Move engine start switch (4) to the OFF position.
Show/hide table
 | |
| Illustration 3 | g03148938 |
- Unlock latches (5) and open engine hood (6) .
Show/hide table
 | |
| Illustration 4 | g03148939 |
- Raise support bar (7) and secure the engine hood.
Show/hide table
 | |
| Illustration 5 | g03148940 |
- Disconnect propel control cable (9) from the propel pump.
Show/hide table
 | |
| Illustration 6 | g03151080 |
- Place direction control valve (8) in the NEUTRAL position.
- Disconnect electrical connector (10) from neutral start switch (11) .
Show/hide table
 | |
| Illustration 7 | g03151082 |
- Insert spoons of Tool (B) into end of connector (10) which is attached to neutral start switch (11). Connect Tool (B) to the "COM" port and "V-Ohms" port on Tool (A). Place dial on Tool (A) into the ALARM position.
- Loosen the locknut while holding neutral start switch (11) .
- If alarm generated by Tool (A) is sounding, rotate neutral start switch (11) clockwise until the audible alarm generated by Tool (A) stops.
- Rotate neutral start switch (11) counterclockwise until the alarm begins to sound.
- Hold neutral start switch (11), and tighten the locknut.
- Remove the tooling, and reconnect neutral start switch connector (10). Reconnect propel control cable (9) .
- Remove and secure support bar (7). Close engine hood (6) .
Caterpillar Information System:
CW14 Pneumatic Compactor Propel System Relief Valve (Pressure Override) - Test and Adjust
CW14 Pneumatic Compactor Propel System Relief Valve (Main) - Test and Adjust
CW14 Pneumatic Compactor Propel System Relief Valve (Charge) - Test and Adjust
CW14 Pneumatic Compactor Propel System Hydraulic Oil Contamination - Test
CW14 Pneumatic Compactor Propel System System Pressure - Release
C27 and C32 Engines for Caterpillar Built Machines Electronic Unit Injector Mechanism
CB14B Vibratory Asphalt Compactor Machine Systems Lines (Steering)
424B Backhoe Loader Axles, Differential and Brakes Service Brake Control - Adjust
CB14B Vibratory Asphalt Compactor Machine Systems Guard (Alternator)
CB14B Vibratory Asphalt Compactor Machine Systems Lifting Gp (Engine Enclosure)
424B Backhoe Loader Axles, Differential and Brakes Parking Brake Control - Adjust
CB14B Vibratory Asphalt Compactor Machine Systems Solenoid (Throttle)
CW14 Pneumatic Compactor Propel System Case Drain Flow for Piston Motor (Axle Propel) - Test
CW14 Pneumatic Compactor Propel System Travel Speed - Check
CW14 Pneumatic Compactor Propel System Parking Brake - Test
CB14B Vibratory Asphalt Compactor Machine Systems Lines (Hydraulic Fan)
CB14B Vibratory Asphalt Compactor Machine Systems Hydraulic Oil Cooler Lines Group
CP56B, CP68B, CS56B and CS68B Vibratory Soil Compactors Machine Systems Lines (Auxiliary Hydraulic)
Cat® Detect Object Detection System Software Version 3 for Certain Wheel Loaders, Wheel Dozers, Quarry Trucks, Off-Highway Truck/Tractors, Motor Graders, and Articulated Trucks Camera - Inspect/Adjust
CP74B, CS74B, CS78B and CS79B Vibratory Soil Compactors Machine Systems Lines (Auxiliary Hydraulic)
Cat® Detect Object Detection System Software Version 3 for Certain Wheel Loaders, Wheel Dozers, Quarry Trucks, Off-Highway Truck/Tractors, Motor Graders, and Articulated Trucks Object Detection Sensor - Inspect/Adjust
Cat® Detect 12 Radar Object Detection System, Software Version 3 Camera - Inspect/Adjust
Cat® Detect 12 Radar Object Detection System, Software Version 3 Object Detection Sensor - Inspect/Adjust
C3.3B and C3.8 Engines for Caterpillar Built Machines Engine Monitoring System