Bank Valve (Main Hydraulic) - Disassemble
Disassemble Procedure
Start By:
- Remove bank valve (main hydraulic).
- Remove bolts (1) .
Show/hide table
Illustration 1 | g02442183 |
- Remove solenoid assembly (2) .
Show/hide table
Illustration 2 | g02442184 |
- Remove coil assembly (3). Remove O-ring seals (4) and (5) .
Show/hide table
Illustration 3 | g02442185 |
Show/hide table
Illustration 4 | g02442186 |
- Remove fittings (6) and O-ring seals (7) .
Show/hide table
Illustration 5 | g02442187 |
- Remove valve assemblies (8) .
Show/hide table
Illustration 6 | g02442237 |
- Remove bolts (9) .
Show/hide table
Illustration 7 | g02442238 |
- Remove bolts (10). Remove solenoid assembly (11) .
Show/hide table
Illustration 8 | g02442240 |
- Remove fittings (12) and O-ring seals (13) .
Show/hide table
Illustration 9 | g02442241 |
- Remove plug assemblies (14) .
Show/hide table
Illustration 10 | g02444538 |
- Remove ring (15) and O-ring seal (16) from plug assembly (14) .
Show/hide table
Illustration 11 | g02444539 |
- Remove valve assembly (17) .
Show/hide table
Illustration 12 | g02444541 |
- Remove O-ring seals (18) .
Show/hide table
Illustration 13 | g02444607 |
- Remove valve assemblies (19) and (20) .
Show/hide table
Illustration 14 | g02444609 |
- Remove O-ring seals (21) and (22) .
Show/hide table
Illustration 15 | g02444610 |
Show/hide table
Illustration 16 | g02444620 |
Caterpillar Information System:
950M, 962M, 950M Z and 962M Z Wheel Loaders Evaporator Coil and Heater Coil - Remove and Install
C7.1 Engines For Caterpillar Built Machines Diagnostic Code Cross Reference
735B and 740B Articulated Trucks Sampling Interval and Location of Sampling Valve
740C EJECTOR Articulated Truck Suspension and Suspension Cylinder Bearings - Lubricate
Nitrogen Pressure Test Unit FT2724 {4150, 4159, 4169, 4170, 4171, 4174, 4175, 4180} Nitrogen Pressure Test Unit FT2724 {4150, 4159, 4169, 4170, 4171, 4174, 4175, 4180}
416F, 420F and 430F Backhoe Loaders Stabilizer Control
440 and 450 Backhoe Loader Mirror - If Equipped
450F Backhoe Loader Alternate Exit
C13, C15, and C18 Tier 4 Interim Engines Data Link - Test
416F2, 420F2 and 430F2 Backhoe Loaders Plate Locations and Film Locations
416F, 420F and 430F Backhoe Loaders Rated Load
Check Clutch Parameters on PM-200 Machines after Clutch Failure{3155} Check Clutch Parameters on PM-200 Machines after Clutch Failure{3155}
C7.1 Engines For Caterpillar Built Machines Diesel Particulate Filter Collects Excessive Soot
Repair Procedures for the Exterior Mirror Mounting Bracket {0679, 7301, 7319} Repair Procedures for the Exterior Mirror Mounting Bracket {0679, 7301, 7319}
415F2 Backhoe Loader Work Tool Flow Control - If Equipped
2011/03/02 An Improved Relay Assembly for the Machine Electronic Control Module Is Now Used on AP655D Asphalt Pavers {1420}
2013/02/25 New Fuel Pressure Regulators Are Used on Certain Machines Equipped with C7 and C9 Engines {1715}
2011/06/16 New Fuel Pressure Regulators Are Used on Certain C7 and C9 Engines {1715}
Installation of the Hood Lift Assist Retrofit on Certain Off-Highway Trucks{7251} Installation of the Hood Lift Assist Retrofit on Certain Off-Highway Trucks{7251}
C7.1 Engines For Caterpillar Built Machines Diesel Particulate Filter Has Low Inlet Pressure
C7.1 Engines For Caterpillar Built Machines Diesel Particulate Filter Temperature Is High
C7.1 Engines For Caterpillar Built Machines Diesel Particulate Filter Temperature Is Low
C7.1 Engines For Caterpillar Built Machines Engine Cranks but Does Not Start
C7.1 Engines For Caterpillar Built Machines Engine Does Not Crank