416F2, 420F2 and 430F2 Backhoe Loaders Caterpillar

Caterpillar products such as engines, transmissions, and major attachments that are not designed for an operator to ride are identified by Serial Numbers.

For quick reference, and as may be required for local regulatory compliance, record the identification numbers in the spaces that are provided below the illustration.

Illustration 1	g01204641

The Product Identification Number (PIN) plate is located on the left side of the machine. The plate may have the following information:

Illustration 2	g02436556

Manufacturer Name and Address ____________________

Model number (A)____________________

Product Identification Number (B)____________________

Service Information Plate (C)____________________

Year of Manufacture Plate (If Required) (D)____________________

CE Plate (If Required) (E)____________________

Country of Origin Info Plate (If Required) (F)____________________

Illustration 3	g01204809
Direct Drive Transmission

Illustration 4	g01204811
Power Shift Transmission

Transmission Serial Number ____________________

Illustration 5	g02456276

Engine Serial Number ____________________

Certification

ROPS/FOPS Structure

These messages are positioned outside the cab near the bottom left corner of the rear window.

Illustration 6	g01211895

Show/hide table

Structural damage, an overturn, modification, alteration, or improper repair can impair this structure's protection capability thereby voiding this certification. Do not weld on or drill holes in the structure. Consult a Caterpillar dealer to determine this structure's limitations without voiding its certification.

This machine has been certified to the standards that are listed on the certification film. The maximum mass of the machine, which includes the operator and the attachments without a payload, should not exceed the mass on the certification film.

Refer to Operation and Maintenance Manual, "Guards (Operator Protection)" for more information.

European Union

Illustration 7	g02010841

This plate is positioned on the bottom left side of plate (1) for the PIN.

Note: The CE plate is on machines that are certified to the European Union requirements that were effective at that time.

For machines compliant to 2006/42/EC, the following information is stamped onto the CE plate. For quick reference, record this information in the spaces that are provided below.

• Engine Power Primary Engine (kW)____________________

• Engine Power for Additional Engine (If Equipped) ____________________

• Typical Machine Operating Weight for European Market (kg)____________________

• Year of Construction____________________

• Machine Type ____________________

Illustration 8	g01120192

This plate is positioned on the bottom left side of plate (1) for the PIN.

Note: The CE plate is on machines that are certified to the European Union requirements that were effective at that time.

For machines compliant to 98/37/EC and 89/392/EEC, the following information is stamped onto the CE plate. For quick reference, record this information in the spaces that are provided below.

• Engine Power Primary Engine (kW)____________________

• Typical Machine Operating Weight for European Market (kg)____________________

• Year of Construction____________________

For the name and address of the manufacturer, and the country of origin of the machine, refer to the PIN plate.

Product Link

If equipped, this message is used to verify the certification of the Product Link as an RF transmitter. The following specifications are provided to aid in ensuring compliance with all local regulations:

Illustration 9	g01222547

Show/hide table

This machine is equipped with a Caterpillar Product Link communication device. When electric detonators are used, this communication device should be deactivated within 12 m (40 ft) of a blast site for satellite-based systems and within 3 m (10 ft) of a blast site for cellular based systems, or within the distance mandated under applicable legal requirements. Failure to do so could cause interference with blasting operations and result in serious injury or death. In cases where the type of Product Link module cannot be identified, Caterpillar recommends that the device be disabled no less than 12 m (40 ft) from the blast perimeter.

This message is located on the control group for the Product Link. The control group is located on the cab rear wall to the right of the operator seat.

If the machine is required to work within 12 m (40 ft) of a blast area, power to the Product Link module must be disconnected.

Consult your Cat dealer with any questions that concern the operation of the Product Link in a specific country.