Wiring Harness (Open Circuit) - Test
An open is a failure of an electrical circuit that results in no flow of electrical current. An open circuit is usually caused by failed electrical wires or a poor connection of electrical connectors. If an electrical wire or a connection is broken, the flow of electrical current through the circuit is interrupted. A normally closed circuit will have less than 5 ohms of resistance. The following procedure explains the test for an open circuit:
ReferenceFor a complete electrical schematic, refer to Electrical System Schematic for the machine that is being serviced.
TEST FOR AN OPEN CIRCUIT.
- Identify the connectors and the wire numbers of the suspect circuits. Use the Electrical System Schematic of the machine to identify the circuits.
- Turn the key start switch and the disconnect switch to the OFF position.
- Disconnect the components from the wiring harness.
- At one of the disconnected harness connections, place a jumper wire from the contact of the suspect wire to frame ground.
- At the other connector of the machine harness, use the multimeter probes to measure the resistance from the contact of the suspect wire to frame ground.
Expected Result: The resistance is less than 5 ohms.
OK - The resistance is less than 5 ohms. The harness circuit is correct.
Stop.
NOT OK - The resistance is greater than 5 ohms. There is an open in the machine harness.
Repair: Repair the machine harness or replace the machine harness.
Stop.
Caterpillar Information System:
Cat® Grade Control Cross Slope for Motor Graders Electrical Connector - Inspect
770G and 772G Off-Highway Truck Machine Systems Steering Column - Assemble
770G and 772G Off-Highway Truck Machine Systems Steering Column - Disassemble
SC-57 Felling Head Felling Head Output Shaft - Install
2011/04/06 Additional Shims Are Now Used In the Truck Body Mounting Group on 777F Off-Highway Trucks {7258}
2011/05/12 A New Air Conditioning Compressor Protection Module Is Now Used for Certain Cat Products {1408}
735B, 740B and 740B EJECTOR Articulated Trucks Machine Systems Metering Pump (Steering) - Test
770G and 772G Off-Highway Truck (OEM) Hydraulic Fan Drive System Fan Drive Troubleshooting
770G and 772G Off-Highway Truck Suspension Cylinder Front Suspension (Cylinder)
Filtration Procedure for Kidney Looping Off-Highway Truck Steering Oil {0680, 4300, 4332, 5050, 7542} Filtration Procedure for Kidney Looping Off-Highway Truck Steering Oil {0680, 4300, 4332, 5050, 7542}
2011/02/09 Plates Improve the Service Life of the Cowling Group on the 797B Off-Highway Trucks {7051, 7155, 7251, 7254, 7267}
Basic Principles of Kidney Loop Filtering Hydraulic Fluid Systems {0680, 0768, 5050, 5056} Basic Principles of Kidney Loop Filtering Hydraulic Fluid Systems {0680, 0768, 5050, 5056}
Cat® Grade Control Cross Slope for Motor Graders Wiring Harness (Short Circuit) - Test
Cat® Grade Control Cross Slope for Motor Graders Module - Replace
994H Wheel Loader Power Train Transmission Control Valve
2011/08/10 New Line Relief Valves are Now Used for Certain Excavators and Mobile Hydraulic Power Units {5069, 5117}
521B and 522B Track Feller Bunchers Machine Systems Travel Motor
994H Wheel Loader Power Train Selector and Pressure Control Valve (Transmission)
770G and 772G Off-Highway Truck Hydraulic Fan Drive System Oil Filter (Case Drain)
770G and 772G Off-Highway Truck Hydraulic Fan Drive System Oil Filter (Hydraulic Fan)
2011/02/02 New Advanced Efficiency Filters Are Now Available for the Transmission Assembly and the Torque Converter Assembly Used on Certain Wheel Loaders {1408, 1435, 3004, 3006, 3067, 5068}
770G and 772G Off-Highway Truck Suspension Cylinder Rear Suspension (Cylinder)
770G and 772G Off-Highway Truck Hydraulic and Braking System Hydraulic Tank (Brake, Brake Cooling, Hoist)
Installation of the v3.2.3 Software for CAES{7604, 7620} Installation of the v3.2.3 Software for CAES{7604, 7620}