Electrical System
充电器正在工作时，切勿从蓄电池上断开任何充电器电路或蓄电池电路电缆。 否则，由某些蓄电池产生的易燃气体可能被火花点燃。
为便于防止因点燃某些蓄电池产生的可燃气体而生成的火花，负极 "-" 电缆应该最后从外接电源连接到主接地位置。
每天检查电线有无松动或擦破。 在发动机起动之前，拧紧所有松动的电气连接。 发动机起动之前，要修理好所有擦破的电线。 请参阅操作和保养手册以了解具体的起动说明。
接地方法
Show/hide table
 | |
| 图 1 | g02407417 |
典型示例 (1) 蓄电池接地 (2) 主接地位置 (3) 起动马达接地 (4) 缸体接地 | |
Show/hide table
 | |
| 图 2 | g02407418 |
典型示例 (5) 蓄电池接地 (6) 缸体接地 | |
为获得发动机的最佳性能和可靠性，必要将发动机电气系统正确接地。 接地不当会造成电路失控和不可靠。
失控的电路会对曲轴的轴承轴颈表面和铝质部件造成损坏。
未安装发动机至机架接地带的发动机可能因电气放电而损坏。
为确保发动机和发动机电气系统工作正常，必须使用与蓄电池直接相连的发动机到机架的接地带。 这种直接相连可通过将发动机接地线直接连接到机架实现。
接地连接应当紧凑、无腐蚀。 发动机交流发电机必须通过一根足以承受其满载充电电流的导线接地到蓄电池的负极 "-" 端子。
发动机的电源连接和接地连接都应从蓄电池的隔离器引出。
Caterpillar Information System:
Guidelines for Routing and Installing Wire Harness Assemblies {1408, 7553} Guidelines for Routing and Installing Wire Harness Assemblies {1408, 7553}
ACCUGRADE Machine Control ; Guidance Products Radio Interface Module (RIM) Client Setup and Configuration Declaration of Conformity
C4.4 Industrial Engine High Pressure Fuel Lines
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders All Wheel Drive Electronic Control System MID 075 - CID 2322 - FMI 14
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders All Wheel Drive Electronic Control System MID 075 - CID 2322 - FMI 02
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders All Wheel Drive Electronic Control System MID 075 - CID 2321 - FMI 14
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders All Wheel Drive Electronic Control System MID 075 - CID 2321 - FMI 02
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders All Wheel Drive Electronic Control System MID 075 - CID 2320 - FMI 14
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders All Wheel Drive Electronic Control System MID 075 - CID 2320 - FMI 02
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders All Wheel Drive Electronic Control System MID 075 - CID 2319 - FMI 14
120M Series 2, 12M Series 2, 140M Series 2 and 160M Series 2 Motor Graders All Wheel Drive Electronic Control System MID 075 - CID 2319 - FMI 02
AP555E and BG555E Asphalt Pavers Propel System Track Roller Frame
C15 and C18 Engines for Caterpillar Built Machines Speed Control - Test
793F AC, 795F AC, and 795F AC XQ Off-Highway Trucks Monitoring System System Schematic
2010/01/29 New Advanced Efficiency Filters Are Now Available {1408, 1435, 3004, 3067, 5068}
C27 and C32 Engines for Caterpillar Built Machines Intake Manifold Air Pressure Is Low
C27 and C32 Engines for Caterpillar Built Machines Oil Contains Coolant
Installing the 342-2683 Machine Enclosure Seal Kit (DEBRIS BARRIER){7000} Installing the 342-2683 Machine Enclosure Seal Kit (DEBRIS BARRIER){7000}
793F Off-Highway Truck Machine Systems Solenoid and Manifold Valve (Rear Axle Fan, Lubrication, Steering) - Disassemble
793F Off-Highway Truck Machine Systems Solenoid and Manifold Valve (Rear Axle Fan, Lubrication, Steering) - Assemble
C27 and C32 Engines for Caterpillar Built Machines Power Is Intermittently Low or Power Cutout Is Intermittent
C27 and C32 Engines for Caterpillar Built Machines Valve Lash Is Excessive
793F Off-Highway Truck Machine Systems Electronic Flasher Assembly - Remove and Install
793F Off-Highway Truck Machine Systems Module (Intermittent Wiper) - Remove and Install