Position Sensor for the Lift Linkage (Electronic Technician) - Calibrate
此校准程序将设定铲斗提升油缸位置传感器的信号限制。 信号限制是指位置传感器发送到机具电子控制模块(ECM)信号的最大和最小占空比。 这将允许机具 ECM 确定提升连杆位于完全升起位置、完全降下位置或提升连杆移动范围内的任何位置。 此校准程序将设定提升连杆位置传感器的信号限制。 信号限制是指位置传感器发送到机具电子控制模块(ECM)信号的最大和最小占空比。 从而允许机具(ECM)确定提升连杆的位置。
注: 当记录了最小占空比时,便根据此位置自动计算得到最大占空比。
校准步骤
- 使机器远离其它运转机器和人员。 将机器放在光滑、水平的表面上。 将铲刀降至地面。 将发动机起动开关转到断开位置。
- 将 Cat ET 连接到机器上。 该接头位于座椅后方、驾驶室右侧。
参考关于使用 Cat ET 的更多信息,请参阅所维修机器的故障诊断与排除, "利用 Caterpillar 电子技师确定诊断代码"。
Show/hide table
图 1 | g01134789 |
Caterpillar 电子技师(ET)的维修接头 |
- 将钥匙起动开关转到接通位置。
- 将 Cat ET 连接到您的笔记本电脑上。 打开 Cat ET 的软件程序。
- 从 "ECM Selector(ECM 选择器)"屏幕上选择 "Implement 836H(机具 988H)"后单击 "OK" 按钮。
Show/hide table
图 2 | g01134802 |
- 在 Cat ET 中选择 "Service(维修)"菜单。 从 "Service(维修)"菜单中选择 "Calibrations(标定)"。 从 "Calibrations(校准)"菜单中选择 "Linkage Sensor Calibrations(连杆传感器校准)"。
Show/hide table
图 3 | g01133933 |
- Cat ET 屏幕将分为三个显示区域。 屏幕顶部用来显示校准中监视的重要状态参数。 屏幕中部显示校准程序方面的信息。 屏幕底部显示校准的逐步指南。 当前需要执行的步骤将以粗体字突出显示。 所有其他步骤将以灰体字显示。
Show/hide table
图 4 | g01133934 |
- 选择 "Next(下一步)"按钮开始标定。 复选标记框将出现在完成步骤的左侧,且下一步将以粗体字突出显示。 成功完成一步后,按 "Next(下一步)"按钮以开始下一步。 执行屏幕底部列出的步骤,直到标定程序完成。
注: 屏幕中部显示用来告知您校准状态的消息。
- 继续按照屏幕上列出的指南去做,直到完成校准。
- 校准完成或选择 "Cancel(取消)"按钮时,Cat ET 将显示状态屏幕。 状态屏幕将通知您校准是否成功。 只有校准成功时,机具 ECM 才保存新校准数据。
- 选择 "Restart(重新开始)"按钮重复校准或选择 "Finish(完成)"完成校准。
- 要退出校准,请选择 "File(文件)"菜单,然后选择 "Exit(退出)"。
Caterpillar Information System:
773F and 775F Off-Highway Truck Power Train Position Sensor (Transmission Control)
2009/11/05 A New Transmission Harness and a New Position Sensor Group Are Now Used on Certain Cat Products {1408, 1439, 3167}
797F and 797F XQ Off-Highway Trucks Towing the Machine
Drain Plug for the Dump Body on 725, 730, 735, and the 740 Articulated Trucks{7250, 7258} Drain Plug for the Dump Body on 725, 730, 735, and the 740 Articulated Trucks{7250, 7258}
CP-663E, CS-663E and CS-683E Paving Compactors and CP-433E, CP-563E, CP-573E, CP44, CP54, CP56, CP64, CP74, CP76, CS-433E, CS-563E, CS-573E, CS-583E, CS433E, CS44, CS54, CS56, CS64, CS74 and CS76 Vibratory Soil Compactors Vibratory Electronic Control Troubleshooting
793F and 797F Off-Highway Trucks Power Train Electronic Control System System Schematic
2009/10/29 Fuel Injection Pump and Fuel Priming Pump {1251, 1258, 1260, 1290}
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Systems Extendable Stick - Remove and Install
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System Diagnostic Code List
793F Off-Highway Truck Machine Systems Gear Pump (Brake, Hoist) - Remove and Install
785D Off-Highway Truck Steering System Front Wheel - Align
CP-663E, CS-663E and CS-683E Paving Compactors and CP-433E, CP-563E, CP-573E, CP44, CP54, CP56, CP64, CP74, CP76, CS-433E, CS-563E, CS-573E, CS-583E, CS433E, CS44, CS54, CS56, CS64, CS74 and CS76 Vibratory Soil Compactors Vibratory Electronic Control Connector Contact Description
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System Position Sensor for the Joystick Control (Electronic Technician) - Calibrate
793F Off-Highway Truck Machine Systems Brake Release Pump and Motor (Parking and Secondary) - Remove and Install
Proper Storage Procedures for Commercial Engines {0355, 1000} Proper Storage Procedures for Commercial Engines {0355, 1000}
793F Off-Highway Truck Machine Systems Brake Release Pump and Motor (Parking and Secondary) - Disassemble
793F Off-Highway Truck Machine Systems Brake Release Pump and Motor (Parking and Secondary) - Assemble
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Systems Cab - Install
C27 and C32 Engines for Caterpillar Built Machines Electrical Connectors
834H Wheel Dozer and 836H Landfill Compactor Electrohydraulic System MID 082 - CID 0352 - FMI 03
914G2 and IT14G2 Compact Wheel Loaders Declaration of Conformity
2009/10/23 An Updated Piston Is Now Used in the Lift Cylinders on Medium Wheel Loader {5102}
797F and 797F XQ Off-Highway Trucks Towing With Power Train Failure
797F and 797F XQ Off-Highway Trucks Engine Starting with an External Air Supply - If Equipped with Air Starting Arrangement