Link Assemblies (Upper) - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-1863     | Retaining Ring Pliers     | 1     |
B     | 1P-0510     | Driver Gp     | 1     |
Start By:
- Release the pressure in the hydraulic system. Refer to Disassembly and Assembly, "System Pressure - Release".
- Use Tooling (A) in order to remove retaining rings (1). Remove retaining rings (1) and washers (2) .
Show/hide table
Illustration 1 | g01665715 |
- Attach a suitable lifting device to tilt cylinder (3). The weight of tilt cylinder (3) is approximately 54 kg (120 lb). Remove link assembly (5) and pin (4) .
Show/hide table
Illustration 2 | g01665716 |
- Lower tilt cylinder (3) onto the loader frame. Remove the suitable lifting device.
- Use Tooling (A) in order to remove retaining ring (6). Remove retaining ring (6) and washer (7). Remove link assembly (8) .
Show/hide table
Illustration 3 | g01665717 |
- Remove pin (10) .
Show/hide table
Illustration 4 | g01665718 |
- Remove pin (9) and link assembly (11) .
- Use Tooling (B) in order to remove bearings (12) and (13) .
Show/hide table
Illustration 5 | g01665921 |
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-1863     | Retaining Ring Pliers     | 1     |
B     | 1P-0510     | Driver Gp     | 1     |
- Use Tooling (B) in order to install bearings (12) and (13) .
Show/hide table
Illustration 6 | g01665921 |
- Position link assembly (11) and install pin (9). Install pin (10) .
Show/hide table
Illustration 7 | g01665718 |
- Install link assembly (8). Use Tooling (A) in order to install retaining ring (6). Install washer (7) and retaining ring (6).
Show/hide table
Illustration 8 | g01665717 |
- Attach a suitable lifting device to tilt cylinder (3). The weight of tilt cylinder (3) is approximately 54 kg (120 lb). Position tilt cylinder (3) and install pin (4). Install link assembly (5) .
Show/hide table
Illustration 9 | g01665716 |
- Use Tooling (A) in order to install retaining rings (1). Install washers (2) and retaining rings (1) .
Show/hide table
Illustration 10 | g01665715 |
Note: Use washers (2) in order to obtain a 1.00 ± 0.50 mm (0.039 ± 0.020 inch) gap.
Caterpillar Information System:
2009/08/24 New Fuel Injection Lines {1251, 1252}
797F and 797F XQ Off-Highway Truck Braking System Solenoid Valve (Rear Axle Motor Unloader)
797F and 797F XQ Off-Highway Truck Braking System Solenoid Valve (Brake Cooling)
MINEGEM Machine Control ; Guidance Products Local Area Radio Network Site Server - Test
MINEGEM Machine Control ; Guidance Products Local Area Radio Network Signal Strength at Machine - Test
MINEGEM Machine Control ; Guidance Products Local Area Radio Network Local Area Radio Network Communications - Test
MINEGEM Machine Control ; Guidance Products Local Area Radio Network Communication to a New Machine - Test
MINEGEM Machine Control ; Guidance Products Local Area Radio Network Communication to Operating Machine - Test
MINEGEM Machine Control ; Guidance Products Local Area Radio Network Communication to Machine at Startup - Test
Procedure to Apply Dielectric Grease to the Horn (Cruise Control) Contact Ring{4310} Procedure to Apply Dielectric Grease to the Horn (Cruise Control) Contact Ring{4310}
CD54 Paving Compactor Potentiometer (Chip Spreader) - Test
795F AC and 795F AC XQ Off-Highway Truck Power Train Electronic Control System MID 081 - CID 3501 - FMI 07
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Machine Systems Cab - Remove
2009/08/17 New Hose Clamps Update the Water Lines Groups {1380}
CD54 Paving Compactor Switch (Sidecutter) - Test
793F Off-Highway Truck Power Train Traction Control System (TCS) Wheel Speed Ring - Remove and Install
793F Off-Highway Truck Power Train Differential and Bevel Gear - Install
CD54 Paving Compactor Solenoid Valve (Chip Spreader) - Test
AP-1055D and BG-2455D Asphalt Pavers Track Roller Frame - Lubricate
793D Off-Highway Truck Engine Supplement Engine and Torque Converter - Remove and Install
C4.4 Industrial Engine Engine Stopping
793F Off-Highway Truck Power Train Torque Converter - Remove and Install
12M Motor Grader Caterpillar Approved Work Tools
793F Off-Highway Truck Power Train Relief Valve (Torque Converter Inlet) - Remove and Install