Wheel, Brake and Suspension (Front) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 1U-9200     | 杠杆式拉拔举倾机构总成     | 2     |
B     | 270-8312     | 支柱拆卸器     | 1     |
C     | 138-7574     | 连杆支架     | 2     |
D     | 355-5007     | 台架组件     | 1     |
E     | 4C-5593     | 防粘结剂     | -     |
- 将轴承 (23) 安装到轴承外圈 (21) 中。 安装挡圈 (22) 。 需要两个人一起安装轴承盖 (21) 。 轴承盖 (21) 的重量约为 68 kg (150 lb)。
Show/hide table
图 1 | g03358478 |
- 使用工具 (B) 以将前轮、制动器和悬架油缸 (17) 从工具 (D) 上拆下。 前轮、制动器和悬架油缸 (17) 的重量约为 5897 kg (13000 lb)。
Show/hide table
图 2 | g03358476 |
- 安装键 (20) 。
Show/hide table
图 3 | g03358475 |
- 使用工具 (B) 以定位前轮、制动器和悬架油缸 (17) 。 前轮、制动器和悬架油缸 (17) 的重量约为 6087 kg (13420 lb)。 将工具 (C) 定位在前轮、制动器和悬架油缸 (17) 下方。
Show/hide table
图 4 | g03358470 |
- 使用工具 (A) 固定车轮组件 (1) ,并防止车轮心轴意外移动。
Show/hide table
图 5 | g03356779 |
前部 |
Show/hide table
图 6 | g03356777 |
后部 |
- 确保悬架油缸 (16) 与键对准。 将工具 (E) 涂敷在螺栓 (19) 、螺栓 (18) 、螺母和垫圈上。 安装螺栓 (19) 、螺栓 (18) 、螺母和垫圈。 对另一侧的悬架油缸 (16) 重复此步骤。
Show/hide table
图 7 | g03358473 |
Show/hide table
图 8 | g03357680 |
Show/hide table
注意 |
---|
使用新的螺栓和螺母安装悬架油缸。 |
- 将工具 (E) 涂敷在螺栓 (15) 、螺母和垫圈上。 安装螺栓 (15) 、螺母和垫圈。 将螺栓 (15) 和螺栓 (19) 拧紧至 1500 ± 150 N·m (1106 ± 111 lb ft) 的扭矩。 将螺栓 (15) 和螺栓 (19) 再转动 60° ± 5°。 对另一侧的悬架油缸 (16) 重复此步骤。
- 将工具 (E) 涂敷在螺栓 (14) 、螺母和垫圈上。 安装螺栓 (14) 、螺母和垫圈。 将螺栓 (14) 和螺栓 (18) 拧紧至 1000 ± 100 N·m (738 ± 74 lb ft) 的扭矩。 将螺栓 (14) 和螺栓 (18) 再转动 60° ± 5°。 对另一侧的悬架油缸 (16) 重复此步骤。
- 请参阅技术规格, "悬架油缸(前)",了解正确的紧固步骤。
- 调整轴承盖两侧,轴承盖和机架之间的间隙。 间隙必须等距。
Show/hide table
图 9 | g03358462 |
注: 如果发动机已拆下进行维修,则在安装垫片 (13) 前必须安装好发动机和管组件。 安装垫片 (13) 前,必须用放置在主机架下方的两个千斤顶均匀支撑机架两侧。
- 安装垫圈 (13) 。
注: 不要用力将垫片 (13) 塞入盖与卡车机架之间的间隙。 只使用足够的垫片 (10) 来填充间隙,使得间隙保持相等。
- 将工具 (E) 涂抹到螺栓 (12) 上。 安装螺栓 (12) 。
- 连接线束组件 (11) 。
Show/hide table
图 10 | g03358458 |
- 连接润滑脂软管组件 (9) 。 安装盖 (10) 。
Show/hide table
图 11 | g03358456 |
- 连接润滑脂软管组件 (8) 。
Show/hide table
图 12 | g03357674 |
- 安装夹子 (7) 。 连接软管组件 (6) 。
Show/hide table
图 13 | g03357671 |
- 连接软管组件 (5) 。 连接软管组件 (4) 。
Show/hide table
图 14 | g03357669 |
- 使用适当的起吊设备定位转向臂 (2) 。 转向臂 (2) 的重量约为 500 kg (1100 lb)。 安装螺栓 (3) 。 拧紧螺栓 (3) 至扭矩为 1800 ± 200 N·m (1328 ± 148 lb ft)。
Show/hide table
图 15 | g03356773 |
- 拆下工具 (A) 。
Show/hide table
图 16 | g03356779 |
前部 |
Show/hide table
图 17 | g03356777 |
后部 |
- 向行车和停车制动器中加满油。 请参阅操作和保养手册, "容量 - 加注"。
- 排出行车和停车制动器中的空气。 请参阅测试和调整, "制动系统空气 - 排除"。
Show/hide table
制动液压系统的机油中存在空气会造成人员伤亡。 系统中存在空气会影响制动器完全发挥作用,且机器上的车轮可能无法停止。 要使制动液压系统正常工作,其中的机油不得存在空气。 |
- 向前轮注油。 请参阅操作和保养手册, "前轮油 – 更换"。
- 向液压油箱中加注机油。 请参阅操作和保养手册, "容量 - 加注"。
- 给悬架油缸充油和氮。 请参阅专门说明书, SEHS9411, "维修非公路卡车的悬架油缸"。
Show/hide table
进行维修之前,应阅读悬挂油缸上的所有警告标签。 释放氮气压力之前,必须先将机器停在平稳的地面上。 释放所有氮气压力之前,切勿对悬挂油缸中的机油进行检查。 除非活塞杆完全缩回,且所有氮气压力都已排尽,否则请勿卸下悬挂油缸上的任何阀门、盖子或螺塞。 悬挂油缸充油、排放或测试和调整过程中,或者提升或降低机器时,不要靠近机器。 机器突然向上或向下移动可能会导致净空高度迅速改变。 忽视此警告可能会导致人身伤亡。 |
End By: 安装前轮胎和轮辋。
Caterpillar Information System:
793F Off-Highway Truck Machine Systems Wheel, Brake and Suspension (Front) - Remove
CD54 Paving Compactor Propel System Hydraulic Schematic (Propel System)
Installation Procedure For Mounting Blocks{0679, 6502} Installation Procedure For Mounting Blocks{0679, 6502}
793F Off-Highway Truck Engine Starting
793F Off-Highway Truck Before Starting Engine
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Drive and Steering Axle (Front) - Install
2009/07/20 Improvements Have Been Made to the Coolant Tank {1353}
793F and 793F CMD Off-Highway Truck Power Train Visual Inspection (Rear Axle and Final Drive)
793F and 793F CMD Off-Highway Truck Power Train Rear Axle and Final Drive System
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Power Train Electronic Control System MID 027 - CID 0127 - FMI 03
CD54 Paving Compactor Propel System Harness (Speed Potentiometer) and Electronic Sensor - Test
14L Motor Grader Power Train Parking Brake
Undercarriage Reconditioning Bulletin Contents {0374, 4150} Undercarriage Reconditioning Bulletin Contents {0374, 4150}
793F and 793F CMD Off-Highway Truck Power Train Rear Wheel Bearing - Adjust - High Capacity Bearings
2009/06/15 A New Cover Plate For the Bottom Guard Is Now Used {7153}
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 0296 - FMI 14
980H Wheel Loader Machine Systems Lubrication Pump (Automatic) - Disassemble
583T Pipelayer Maintenance Interval Schedule
793F and 793F CMD Off-Highway Truck Braking System Solenoid Valve (Brake Accumulator Purge)
CP44 and CS44 Vibratory Soil Compactors C4.4 Engine Supplement Air Cleaner - Remove and Install
793F and 793F CMD Off-Highway Truck Braking System Solenoid Valve (Parking, Secondary Brake)
980H Wheel Loader Machine Systems Lubrication Pump (Automatic) - Assemble
120M, 12M, 140M, 14M, 160M and 16M Motor Graders Power Train Electronic Control System Features
793F and 793F CMD Off-Highway Truck Braking System Pressure Reducing Valve (Pilot Oil)