Sensor - Adjust - Blade Slope Sensor
The blade slope sensor must be within .3 degrees of being parallel to the cutting edge. The following information demonstrates the procedure for checking the alignment.
Show/hide table
| |
| Illustration 1 | g01285332 |
|
Top View of the Blade Slope Sensor (1) Blade (2) Straight Edge (3) Blade Slope Sensor | |
- Place one end of a 4 foot straight edge against the vertical edge of the blade slope sensor.
- Hang a plumb bob off the other end of the straight edge.
Show/hide table
Illustration 3 g01285466 - Measure the horizontal distance from the blade to the string line of the plumb bob. Note the measurement.
- Repeat Step 1 through Step 3 for the other side of the blade.
- Subtract the two measurements.
The result should be less than
12.7 mm (0.5 inch) .If the result is greater than
12.7 mm (0.5 inch) proceed to Step 6. Otherwise, the blade slope sensor is properly mounted. - Loosen the bolts on the blade slope sensor.
- Rotate the blade slope sensor in the direction that is needed.
- Tighten the bolts.
- Recheck the measurements.
If the result is greater than
12.7 mm (0.5 inch) , proceed to Step 10.Otherwise, the blade slope sensor is properly mounted.
- Remove the bracket for the blade slope sensor. Reweld the bracket.
Note: The fore/aft pitch of the bracket must be within 3 degrees of the fore/aft pitch of the platform (circle).
Show/hide table
| |
| Illustration 2 | g01285398 |
Caterpillar Information System:
AccuGrade® (CD610) Sensor - Adjust - Mainfall Sensor
2009/02/16 A New Lamp Group (Beacon) is Now Used {1429, 1431}
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines ECM Will Not Accept Factory Passwords
416E Backhoe Loader Parking Brake - Check/Adjust
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Programming Parameters
416E Backhoe Loader Braking System - Test
2009/04/20 A New Gas Spring Assembly is Available {4338}
587R Pipelayer Mirror - If Equipped
414E, 416E, 420E and 430E Backhoe Loaders Machine Systems Bank Valve (Backhoe) - Remove
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System MID 081 - CID 1403 - FMI 06
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System MID 081 - CID 1403 - FMI 05
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 1403 - FMI 03
AccuGrade® (CD610) Sensor - Adjust - Rotation Sensor
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 1403 - FMI 11
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 1404 - FMI 03
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System MID 081 - CID 1404 - FMI 05
AccuGrade® GPS v11 for CD700 General Information
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System MID 081 - CID 1404 - FMI 06
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Engine Cranks but Will Not Start
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 1404 - FMI 11
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 1405 - FMI 03
414E, 416E, 420E and 430E Backhoe Loaders Machine Systems Bank Valve (Backhoe) - Install
2009/02/23 A New Pressure Switch Is Now Used {1435}
793F CMD Off-Highway Truck (Command for Hauling) Power Train Electronic Control System MID 081 - CID 1405 - FMI 05