Specifications
Illustration 1 | g01621120 |
(1) 111-4343 Pin
- Pin diameter ... 39.95 to 40.00 mm (1.573 to 1.575 inch)
- Bore for the pin ... 40.130 ± 0.025 mm (1.5799 ± 0.0010 inch)
Note: As required, use the following washer in order to provide a maximum clearance of 1.0 ± 0.5 mm (0.04 ± 0.02 inch):
(2) 119-4594 Washer
- Quantity ... 8
- Thickness of one washer ... 1.0 mm (0.04 inch)
(3) 122-4954 Pin As
- Pin diameter ... 39.95 to 40.00 mm (1.573 to 1.575 inch)
- Bore for the pin assembly ... 40.130 ± 0.025 mm (1.5799 ± 0.0010 inch)
Illustration 2 | g01621151 |
(4) Tilt cylinder (5) Link (7) Lift cylinder |
(6) 130-5451 Pin
- Pin diameter ... 44.95 ± 45.00 mm (1.770 ± 1.772 inch)
- Bore for pin in the sleeve bearing after installation ... 45.213 ± 0.058 mm (1.7800 ± 0.0023 inch)
Illustration 3 | g01622272 |
(8) 111-4342 Pin
- Pin diameter ... 44.95 to 45.00 mm (1.770 to 1.772 inch)
- Bore for the pin ... 45.130 ± 0.025 mm (1.7768 ± 0.0010 inch)
Note: After assembly of the sleeve bearings, coat all the bores and sleeve bearings with 5P-0960 Grease Cartridge after cleaning and before painting.
(9) 9R-6690 Sleeve Bearing
- Quantity ... 4
- Inside diameter ... 60.315 ± 0.020 mm (2.3746 ± 0.0008 inch)
- Outside diameter ... 73.111 ± 0.013 mm (2.8784 ± 0.0005 inch)
- Inside diameter ... 60.315 ± 0.020 mm (2.3746 ± 0.0008 inch)
(10) As required, use the following spacers in order to provide a maximum clearance of 1.0 mm (0.0394 inch). Position the spacers in order to equalize the clearance within 3 mm (0.1 inch) between the wear bars on the lift arms and the wear bars on the radiator guard for each side of the machine.
-
128-7903 Spacer
- Quantity ... 2
- Thickness of one spacer ... 3 mm (0.1 inch)
-
128-7905 Spacer
- Quantity ... 2
- Thickness of one spacer ... 1.0 mm (0.0394 inch)
(11) 111-4340 Pin
- Pin diameter ... 59.950 to 60.000 mm (2.3602 to 2.3622 inch)
- Bore diameter for pin in the sleeve bearing after installation ... 60.237 ± 0.046 mm (2.3715 ± 0.0018 inch)
Note: As required, use the following washer in order to provide a maximum total clearance of 1.0 mm (0.04 inch).
(12) 9R-8390 Spacer
- Quantity ... 2
- Thickness of one spacer ... 1.0 mm (0.04 inch)
Note: As required, use the following washer in order to provide the maximum clearance of 1.0 ± 0.5 mm (0.04 ± 0.02 inch).
(13) 111-4337 Washer
- Quantity ... 14
- Thickness of one washer ... 1.0 mm (0.04 inch)
(14) 9R-0411 Sleeve Bearing
- Quantity ... 4
- Inside diameter ... 45.295 ± 0.020 mm (1.7833 ± 0.0008 inch)
- Outside diameter ... 58.082 ± 0.013 mm (2.2867 ± 0.0005 inch)
- Inside diameter ... 45.295 ± 0.020 mm (1.7833 ± 0.0008 inch)
(15) 111-4334 Pin
- Pin diameter ... 44.95 to 45.00 mm (1.7697 to 1.7717 inch)
- Bore for the pin in the sleeve bearing after installation ... 45.238 ± 0.046 mm (1.7810 ± 0.0018 inch)
(16) 116-4825 Sleeve Bearing
- Quantity ... 4
- Inside diameter ... 45.198 ± 0.020 mm (1.7794 ± 0.0008 inch)
- Outside diameter ... 58.584 ± 0.013 mm (2.3065 ± 0.0005 inch)
- Inside diameter ... 45.198 ± 0.020 mm (1.7794 ± 0.0008 inch)
(17) 111-4341 Pin
- Pin diameter ... 44.95 to 45.00 mm (1.7697 to 1.7717 inch)
- Bore for the pin in the sleeve bearing after installation ... 45.139 ± 0.046 mm (1.7771 ± 0.0018 inch)
(18) As required, use the following washer in order to provide the maximum clearance of 1.0 ± 0.5 mm (0.04 ± 0.02 inch):
-
119-4594 Washer
- Quantity ... 6
- Thickness of one washer ... 1.0 mm (0.04 inch)
(19) 114-3836 Pin
- Pin diameter ... 39.95 to 40.00 mm (1.573 to 1.575 inch)
- Bore for the pin ... 40.225 ± 0.025 mm (1.5837 ± 0.0010 inch)
Illustration 4 | g01622358 |
(20) 111-4343 Pin
- Pin diameter ... 39.95 to 40.00 mm (1.573 to 1.575 inch)
- Bore for the pin in the sleeve bearing after installation ... 40.135 ± 0.046 mm (1.5801 ± 0.0018 inch)
(21) 116-4825 Sleeve Bearing
- Quantity ... 2
- Inside diameter ... 45.198 ± 0.020 mm (1.7794 ± 0.0008 inch)
- Outside diameter ... 58.584 ± 0.013 mm (2.3065 ± 0.0005 inch)
- Inside diameter ... 45.198 ± 0.020 mm (1.7794 ± 0.0008 inch)
Illustration 5 | g01622377 |
Section J-J |
(22) 9R-1496 Sleeve Bearing
- Quantity ... 2
- Inside diameter ... 40.196 ± 0.020 mm (1.5825 ± 0.0008 inch)
- Outside diameter ... 53.576 ± 0.013 mm (2.1093 ± 0.0005 inch)
- Inside diameter ... 40.196 ± 0.020 mm (1.5825 ± 0.0008 inch)
(23) 125-1037 Pin As
- Pin diameter ... 44.95 ± 45.00 mm (1.7697 ± 1.7717 inch)
- Bore for the pin in the sleeve bearing after installation ... 45.139 ± 0.046 mm (1.7771 ± 0.0018 inch)
Loader Arrangement
Linkage Assembly
Removal Procedure
- Remove retaining rings (1) . Remove plate (2) . Remove retaining rings (4) . Remove link assembly (5) . Remove plate (3) .
Illustration 6 | g01625920 |
- Repeat for opposite side of the loader.
Installation Procedure
- Install link assembly (5) in the reverse order of removal.
- Install shims as required, to obtain a maximum total clearance of 1.0 ± 0.5 N·m (9 ± 4 lb in).
Loader Arrangement
Removal Procedure
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 180-3033     | Repair Stand Set     | 1     |
B     | 8S-7690     | Stud     | 1     |
8S-7621 | Tube     | 1     | |
8S-7615 | Pin     | 2     |
- Remove the tilt cylinders.
- Remove the quick coupler.
- Place Tooling (A) under the rear of the machine, as shown.
Illustration 7 | g00759798 |
- Install Tooling (B) under the loader frame.
Illustration 8 | g01626470 |
- Remove pin (5) and the washers. Note the location of washers in order to aid in installation. Lower lift cylinder (7) . Disconnect harness assembly (1) .
Illustration 9 | g01626474 |
- Disconnect hose assembly (6) . Repeat for the other side.
- Remove link assembly (2) . Attach a suitable lifting device to loader assembly (3) . The weight of loader assembly (3) is approximately 408 kg (900 lb). Remove pin (4) . Remove loader assembly (3) .
Installation Procedure
- Install loader assembly (3) in the reverse order of removal.
- Refer to Loader Arrangement Specifications section for the correct shimming procedure.