CP54 and CS54 Vibratory Soil Compactors Machine Systems Caterpillar

Show/hide table

Personal injury can result from rotating and moving parts. Stay clear of all rotating and moving parts. Never attempt adjustments while the machine is moving or the engine is running unless otherwise specified. The machine must be parked on a level surface and the engine stopped. Attach a "Do Not Operate" or similar warning tag to the start switch and controls before servicing, repairing, or making adjustments to the machine.

Show/hide table

Personal injury or death can result from sudden machine movement. Sudden movement of the machine can cause injury to persons on or near the machine. To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.

Show/hide table

Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the attachments have been lowered, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.

Note: If loose, uncompacted soil is unavailable, drive the machine onto a unusable tire without rims. This tire should have substantial stiffness in order to support the drum. If tires are used, the drum should be a minimum of 102 mm (4 inch) above the ground.

1. Drive the machine to a smooth, horizontal surface on loose, uncompacted soil.

Show/hide table



Illustration 1	g01415204

2. Move propulsion lever (1) to the NEUTRAL position.

Show/hide table



Illustration 2	g01415246

3. Move parking brake switch (2) to the ON position.

Show/hide table



Illustration 3	g01415249

4. Move throttle control switch (3) to the LOW IDLE position.

Show/hide table



Illustration 4	g01415252

5. Move engine start switch (4) to the OFF position.

Note: The cab can be tilted in order to provide greater access to components under the cab. However, the cab must be lowered and fastened before the machine is operated. Refer to Disassembly and Assembly, KENR6047, "Cab - Tilt".

6. Connect Tool (A) to Tool (B). Make two sets of tools.

Show/hide table



Illustration 5	g01416243
Left side view of the Vibrator Pump .

7. Remove the cap from port "Mb" (5). Connect one Tool (B) to the low amplitude pressure tap in port "Mb" (5) on the vibratory pump.

Show/hide table



Illustration 6	g01416239
.

8. Remove the cap from port "Ma" (6). Connect second Tool (B) to the high amplitude pressure tap in port "Ma" (6) on the vibratory pump.

9. Move engine start switch (4) to the START position. Release the switch when the engine starts.

10. Operate the engine at low idle for few minutes. Move throttle switch (3) to the HIGH IDLE position.

11. Monitor hydraulic oil temperature with Tool (C). Operate the machine until the oil temperature reaches 43 ± 5.6 °C (110 ± 10 °F).

Show/hide table



Illustration 7	g01416251

12. Move switch (7) for amplitude to the LOW AMPLITUDE position.

Show/hide table



Illustration 8	g01416254

13. Actuate vibratory switch (8) on the propulsion lever.

14. Watch the pressure at port "Mb" (5). Record the initial pressure reading as the main relief pressure. The initial pressure reading will be a momentary spike on the gauge. After the initial spike, the hydraulic pressure will return to normal. The main relief pressure should be 35000 ± 3000 kPa (5075 ± 435 psi).

15. Actuate vibratory switch (8) in order to stop the vibratory system.

16. Move switch (7) for the amplitude to the HIGH AMPLITUDE position.

17. Actuate vibratory switch (8) on the propulsion lever.

18. Watch pressure at port "Ma" (6). Record the initial pressure reading as the main relief pressure. The initial pressure reading will be a momentary spike on the gauge. After the initial spike, the hydraulic pressure will return to normal. The main relief pressure should be 35000 ± 3000 kPa (5075 ± 435 psi).

19. Actuate vibratory switch (8) in order to stop the vibratory system.

20. Move throttle switch (3) to the LOW IDLE position.

21. Move engine start switch (4) to the OFF position.

22. If the pressure is inside the specified range, go to 25. If the pressure is outside the specified range, go to Step 23.

Show/hide table



Illustration 9	g01416256
Low Amplitude Relief Valve

Show/hide table



Illustration 10	g01416264
High Amplitude Relief Valve

23. Use the following procedure to adjust the main relief valves:

    1. Remove cap (9) or cap (10) from the relief valve.

    2. Remove the relief valve cartridge from the pump. Reinstall cap (9) or cap (10) in order to prevent oil from leaking from the ports.
    Show/hide table
    
    

    Illustration 11	g01416271
    Arrows indicate the clamping position.

    3. Clamp the relief valve cartridge in a soft vise jaw. Loosen locking the setscrew (11) with a 3 mm Allen wrench.

    4. Use a 5 mm wrench to turn spindle (12). Turn the spindle clockwise in order to increase pressure. Turn the spindle counterclockwise in order to decrease pressure.

       Note: One full revolution of spindle (12) changes the pressure setting by approximately 4400 kPa (638 psi).

    5. Tighten locking setscrew (11) .

    6. Remove the relief valve cartridge from the vise.

    7. Remove cap (9) and cap (10) for the relief valve. Install the relief valve cartridge in the vibration pump. Reinstall the cap for the relief valve.

24. Go to Step 9.

25. Remove Tool (B) from port "Ma" (6) and from port "Mb" (5). Reinstall rubber caps.