Fuel Transfer Pump - Remove
拆卸步骤
Show/hide table
| 注意 |
|---|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何工作之前，请参阅操作和保养手册, "一般危险信息和高压燃油管路"以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息，请参阅系统运作，测试和调整, "燃油系统部件清洁度"。 |
Show/hide table
| 注意 |
|---|
在检查、保养、测试、调整及维修产品时，请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前，请准备好盛接液体用的适当容器。 按照本地法规和要求处置所有油液。 |
- 将燃油供应转到断开位置。
- 将塑料管组件 (7) 从输油泵 (2) 上卸下。
注: 如果管组件有快接接头，确保插接管组件之前接头清洁。
Show/hide table
 | |
| 图 1 | g01334899 |
典型示例 | |
- 将塑料管组件 (5) 从输油泵 (2) 的出口断开。
注: 如果管组件有快接接头，确保插接管组件之前接头清洁。
- 将接头 (6) 从输油泵 (2) 上拆下。 将 O 形密封圈从接头 (6) 上拆下。
如有必要，将接头 (9) 从输油泵 (2) 上卸下。 将 O 形密封圈从接头 (9) 上拆下。
- 将燃油回油管组件 (8) 从输油泵和缸盖上拆下。
注: 先断开输油泵处的管组件，以便将燃油从缸盖排出。
- 将发动机机油供油管组件 (4) 从喷油泵 (1) 上拆下。
- 立即用新螺塞或盖子塞住或盖住所有开口和管组件。
- 用球头内六角扳手拆卸将输油泵固定在喷油泵 (1) 上的六角头螺钉 (3) 。
- 将输油泵 (2) 从喷油泵 (1) 上拆下。
注: 请勿拆下喷油泵的定位销 (10) 。
Show/hide table
 | |
| 图 2 | g01335043 |
- 将 O 形密封圈 (11) 从输油泵 (2) 上拆下。
Show/hide table
 | |
| 图 3 | g01335045 |
Caterpillar Information System:
C6.6 Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install - Secondary Fuel Filter
24M Motor Grader Power Train Electronic Control System MID 027 - CID 0679 - FMI 13
EquipmentManager Dealer Administrator Manual Maintenance Watch
24M Motor Grader Power Train Transmission
24M Motor Grader Power Train Electronic Control System MID 027 - CID 0679 - FMI 06
3412E Engine for Caterpillar Built Machines Oil Pressure Is Low
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Track Drive - Remove
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Valve (Stabilizer)
C15 and C18 Generator Set Engines Radiator Core - Remove and Install - Jacket Water Heater
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Control Valve (Boom)
3176C, 3406E and 3456 Industrial Engines Exhaust Temperature Is High
770 and 772 Off-Highway Truck/Tractors Steering Link - Remove and Install
C6.6 Engines for Caterpillar Built Machines Fuel Transfer Pump - Install
C6.6 Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Injection Lines - Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Remove
C6.6 Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Install
C6.6 Engines for Caterpillar Built Machines Turbocharger - Remove - Side Mounted Turbocharger
C6.6 Engines for Caterpillar Built Machines Turbocharger - Remove - Turbocharger Top Mounted
C6.6 Engines for Caterpillar Built Machines Turbocharger - Disassemble
C6.6 Engines for Caterpillar Built Machines Turbocharger - Assemble